General Shale Brick, Inc.

An employee was adjusting a paint roller when his left ring finger was caught in a chain and sprocket. The fingertip was amputated.

An employee was operating a slab line in a plant that produces 16" x 9" x 3" concrete slabs that weigh approximately 25-30 pounds. The employee went to adjust the chain and sprocket for the doubler that stacks the slabs two high, when their right middle finger was caught in the machine. The employee sustained a partial transphalangeal amputation of the finger.

Two employees were shoveling out a machine. The blade of a shovel struck the injured employee's left middle finger, causing a partial amputation.

An employee was behind a brick firing machine aligning bricks for production when the employee was caught between the pusher bar and the setting head, resulting in a fractured pelvis. The machine was energized and was not locked out/tagged out at the time.

An employee was repositioning slabs of brick on a conveyor after noticing they were coming out of the pusher area sideways. While adjusting the slabs, a slab of bricks fell onto the employee's right index finger, resulting in amputation.

An employee was working to build an electrical substation. He was cleaning out the inside of a fixed section of a PVC pipe on the end that was furthest from an excavator. The excavator was outside of the trench and more than 25 feet away when it moved a pipe, pinching the employee's right arm between the two pipes. The employee's forearm was fractured.

An employee was anchored to a movable piece of equipment called a "lid" with a self-retracting lifeline harness. An overhead crane lifted the equipment, causing the employee to be pulled by his harness. The employee was pulled off the walkway and swung over the wall of the kiln. His body and head struck the wall. The employee lost consciousness and sustained a laceration to the side of his head that required stitches. The employee also sustained multiple fractured ribs and fractured vertebrae.

An employee was in a scissor lift, preparing to strip formwork from the underside of a concrete deck. As the lift was ascending, the employee's left little finger was pinched between the lift rail and the concrete beam above. The employee was hospitalized, and the soft tissue of their left little fingertip was amputated; the finger's bony tuft was also damaged.

An employee was operating an order picker when his left middle finger was crushed between the lift and storage racking. The employee's fingertip was amputated.

An employee was ascending in a scissor lift when his left thumb was caught between between the railing of the lift and a piece of equipment installed in the ceiling. The employee's thumb tip was amputated.

An employee was sorting sucker rods. His right hand was caught in the area where the rod hits up against the frame and his index fingertip was amputated just below the nail.

An employee was using a powered miter saw to cut 2x4's. The saw blade hit something inside a board (possibly a hidden nail) and jumped, causing a laceration to the employee's left forearm. The employee was hospitalized with soft tissue and tendon injuries that required surgery.

A crane had been used to set a steel plate on a steel frame. An employee was trying to remove a clamp from the plate when the plate fell and crushed the tip of his left little finger. The employee sustained a fingertip amputation.

An employee was operating a scissor lift, raised to a height of about 15 feet, to inspect an overhead crane rail. The crane itself was being moved. Its hook swung into the scissor lift s arms, causing the lift to tip over onto its side, which in turn caused the lift and the employee to fall to the floor. The employee suffered injuries including broken ribs, spinal fractures, scapula fractures, and internal injuries.

A technician was operating a crane hoist to lift/remove a cylinder head from the main engine (port). The load was lifted at an angle, causing the cylinder head to get stuck on the cylinder head studs. When it became free from the studs, the cylinder head swung. It struck the technician and caught them against the cabinet door. This resulted in an amputation of their left index fingertip at the distal knuckle.

An employee was helping to lift the grating from a floor draining system when the grating slipped and landed on his hand, resulting in the amputation of his right middle finger at the first joint.

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

During a workshop meeting in a hotel, an employee heard a drilling noise, so he walked outside to see what it was. An explosion occurred (possible gas line) and his face, ear, and hair were burned. He also fell and sustained a pelvic fracture.

An employee slipped on condensation on a walkway in a parking garage. She fell and suffered a closed fracture to the neck of the left femur.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.