Peek Pavement Marking LLC

An employee performing thermoplastic handwork at an intersection was struck by a vehicle in his work zone resulting in a broken leg that required surgery and head injuries that required staples.

On April 22, 2024, a highway construction employee was working on pavement markings on an interstate when a passing vehicle struck them, resulting in a fractured leg and hospitalization.

An employee was operating a truck behind a vehicle laying down road striping. A tractor-trailer veered into the work zone, striking the employee's truck. The employee suffered back, neck, hip, and head injuries and was hospitalized.

An employee was part of a crew that was placing stop bars, turn arrows, and crosswalks at an intersection. A vehicle entered the work zone and struck the thermoplastic handliner, which the crew was using to apply the roadway markings. The handliner is a small hand machine that uses molten thermoplastic (430 degrees F) to produce the markings. The impact of the vehicle on the handliner caused the molten material to splatter onto the injured employee, who suffered burns to the neck, right side of the face, and right ear.

An employee was painting a newly paved road when a vehicle struck him, breaking both of his legs and one of his shoulders.

An employee was blowing grass clippings while performing landscaping activities near the shoulder of the road. A vehicle mounted the curb and struck the employee. The road was wet at the time. The employee sustained injuries to their head and lower body.

An employee was flagging at an intersection when a vehicle struck them, resulting in an injury to their left leg.

An employee was flagging traffic on a worksite when they stepped back and were struck by a roller. The employee sustained torn ligaments and a degloving of their left ankle.

An employee was picking up tree branches along the side of the highway when they were struck by a tree trimming machine. The employee was hospitalized with fractures to their ribs and a tibia.

An employee was performing quality assurance at an on-ramp when a mini-excavator with rubber tires rolled over his feet, resulting in fractures to both feet, a fractured right ankle, and a laceration on his right foot.

An employee was operating a battery-powered broom to clean demolition debris off the top of the outermost bridge girder. The girder was approximately 11 feet above the demolition scaffold below. The employee fell approximately 8 feet to wind bracing below. The employee was hospitalized with a pelvis/tailbone fracture. Fall protection was in place at the time.

An employee was cleaning out an inlet pipe in a stormwater structure. The employee stepped back, fell into the pipe, and landed on concrete 13 feet below, at the bottom of the structure. He suffered a broken back.

A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.

An employee was operating a roller and paving a small pathway next to a pavilion. The ground was on a slight pitch, causing him to reach up toward the roll cage to stabilize himself. His right fifth finger was pinched between the roll cage and the rafter of the pavilion. The employee sustained a partial degloving injury with partial traumatic amputation.

An employee was working with paving equipment and heard a noise on the opposite side of the machine he was working on. When the machine stopped, the employee went to the opposite side and crouched down to investigate the noise. A mini track loader backed up and drove over the employee's leg. The employee sustained fractures to their lower leg, ankle, and foot.

An employee was helping to lift the grating from a floor draining system when the grating slipped and landed on his hand, resulting in the amputation of his right middle finger at the first joint.

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

During a workshop meeting in a hotel, an employee heard a drilling noise, so he walked outside to see what it was. An explosion occurred (possible gas line) and his face, ear, and hair were burned. He also fell and sustained a pelvic fracture.

An employee slipped on condensation on a walkway in a parking garage. She fell and suffered a closed fracture to the neck of the left femur.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.