Quad Graphics Inc

An employee was trying to remove a blockage in a dust collection system. The airlock fan activated and amputated three fingertips on the employee's right hand.

Maintenance employees were replacing a gear box in the stacker of a press. After the replacement was complete, the stacker was restarted. The maintenance employees then heard a loud noise coming from the drive chain area and the injured employee went to check the chain tension when the machine amputated his right index fingertip.

While walking towards the office inside the warehouse, an employee slipped on a piece of debris (green strap) that was on the floor and fell. The employee sustained a fractured right hip.

An employee was helping to change out a cylinder on a press. He was putting the cylinder arms down to put the cylinder in place. As he stepped over the driveshaft to pull the pin and roll the cylinders, he lost balance and started to fall forward. He dropped the cylinder arm to regain his balance and the arm came down on his right index finger and amputated the fingertip.

An employee was setting up a machine for a weekend run. The metal door closed on the employee's left index finger, causing a partial amputation.

An employee fell while exiting a trailer. The employee landed on their left side on the pavement, suffering multiple broken ribs on the left side. The employee was hospitalized.

A driver was exiting his vehicle outside the plant gate when his foot slipped on the top step of the truck. He fell to the ground, landed on his left hip and elbow. The employee was hospitalized with a fractured hip/femur.

Two employees were removing a service lift platform from the back of a radar system. While handling the service lift platform, employee 2 was standing on the back of the radar and lost their footing, causing the service lift platform to shift and fall. The injured employee then fell from the top of the platform electronic subsystem (PES) to the floor, approximately 56 inches. The injured employee fractured his left elbow and left hip.

An employee fell from a loading dock to the ground 2-3 feet below. She suffered a compound fracture of the left hip and was hospitalized, requiring surgery.

An employee assisted in cleaning material from a conveyor pit. After the pit was cleaned, the employee proceeded to replace metal safety plates to ensure other employees did not fall into the pit. While replacing one of the last plates, the employee mis-stepped and fell approximately 5 feet into the pit. The employee was hospitalized with back/side bruising, elbow bruising, bone bruises, and/or fractured ribs.

An employee tripped over an object and fell to the ground, resulting in right elbow and right hip fractures.

An employee opened a 480-volt breaker box and reached inside the breaker box when an uninsulated tool came in contact with one of the legs, causing him to be electrocuted. The employee's arm also got caught on the box, resulting in breaks to both bones in the forearm.

An employee was operating a UV coater machine when it began to make a grinding noise. The employee was investigating the vibration of the machine when a gear caught their right index finger and amputated the tip.

A temporary employee was operating a seal machine to seal paper bundles. A jam occurred when the paper and plastic did not properly align to secure the seal. The employee went to clear the jam and the blade on the machine amputated their right middle finger.

An employee was threading the web on a press when his hand was caught between the impression cylinders. Four of the employee's fingers were amputated.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.