Vehicle or machinery fire · Thermal burns degree unspecified
At a glance
Federal OSHA recorded a severe workplace injury
at Pine Tree Food Equipment, 33 Edgemont Drive, PRESQUE ISLE, MAINE 04769
on — Thermal burns degree unspecified, affecting the Head and extremities.
Final narrative
An employee and co-worker arrived at a customer site to work on a six-burner range oven. Upon arrival, they found the gas lines were flooded with water and the oven was waterlogged. They turned off the gas to hook up a safety valve and thermostat to the main gas line. They turned the gas back on and started to do a leak check with leak detection solution. They sprayed fittings, lines, and connections on valves. There was no indication of leaks. They turned the gas on and went to light pilots to test the gas. Upon lighting the pilots, there was a flash that came out of the front valve and the back of the oven. The injured employee was standing in front of the oven and suffered burns to their arms, hands, and face.
Hospitalized Head and extremities Cooking and food-warming machinery except pressurized
An employee was on a roof repairing a belt on a food HVAC system hood. The employee tripped, fell from the roof, and suffered possible broken ribs and lacerations to the chest.
Employees were securing the fuel line of an outboard motor in preparation for removing the motor from a small vessel located in the equipment yard. A gasoline-related fire occurred and one employee sustained burns to both hands and forearms.
Two employees were replacing cartridge filters at the recycle oil filter in a hydrocracking unit. While removing compression springs from the top of the filters located within the filter pot, vapors that had accumulated within the filter tubes ignited, causing a flash fire. Both employees suffered burns to multiple body parts and were hospitalized.
An employee was performing diagnostic work on a vehicle engine. As the employee was leaning over the front of the vehicle, the engine was activated. A fuel leak had produced fumes around the engine, and the ignition spark ignited them. The employee suffered second-degree burns to both hands, both biceps, and the upper chest area.
An employee was checking the fuel level of a ride-on sprayer. While refueling the sprayer, fuel ignited and the employee sustained burns to their jaw and right thumb.
Two employees were working in the kitchen area of a food trailer. There was a sudden burst of fire in the kitchen, and both employees were engulfed by deflagration of gas which oriented from a propane-powered griddle. They suffered first-, second- and third-degree burns to their head, face, arms, and legs.
More severe injuries in this industry (NAICS 811412)
An employee was using a grinder to cut benches for a condenser change-out. The grinder kicked back and lacerated the employee's left hand above the knuckle, cutting tendons. The grinder's cutting wheel was unguarded at the time.
An employee was moving dies on a hydraulic pan brake closer together so he could bend pieces of sheet metal. The employee's left index, middle, and ring fingers were crushed in the machine, and all three fingers were amputated.
An employee was performing preventive maintenance on a dryer at a commercial laundry facility. The emergency stop was released, and the dryer broke his left humerus and lacerated his left forearm.
An employee was on a scissor lift, moving a jug of refrigerant onto a roof. The container fell onto his left middle finger, crushing it against the handrail of the scissor lift and and fracturing it.
An employee was replacing the gauge glass of a boiler while standing on the first rung of a 4-foot ladder. He was loosening a corroded valve when the valve snapped off. Steam and hot water discharged onto the employee's upper body. He was hospitalized with second-degree burns to his face, neck, chest, arms, and hands.
A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.
Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.
An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.
An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.