Struck by rolling, sliding, or shifting objects non-running · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at 4X Construction Group LLC, 3500 S Gun Club Rd, AURORA, COLORADO 80018
on — Fractures , affecting the Leg(s) unspecified.
Watch 4X Construction Group LLC — freeGet an email when a new federal OSHA severe-injury report for 4X Construction Group LLC is published. One employer, no account, unsubscribe in one click.
Final narrative
An employee was greasing a pipe at the bottom of the hill to prepare it to be placed inside another PVC pipe. An excavator was working at the top of the hill about 10 feet away from a pile of 30-inch PVC pipes placed behind a berm. The vibration caused the pipes to dislodge from the berm and a pipe rolled down the 8-10-foot slope. The employee's right leg was caught between the fixed pipe he was working on and the pipe that rolled down the slope and fractured.
Hospitalized Leg(s) unspecified Pipes and tubes plastic, PVC, rubber
An employee was using his left hand to push an axle down the line on a raised track work area while holding the remaining axle back with his right hand. A finger on his right hand was caught between the rail and the dust guard of the axle, resulting in a fracture and a laceration.
An employee was moving metal out of a cart. He had removed one piece and was working to move another when the metal shifted. His right ring finger was crushed between the two pieces, and he suffered a partial amputation to the finger pad at the tip.
A load of steel angles was being lowered when the lifting chain hit the load, causing it to slide toward an employee. An angle slid and pinched the employee, catching both of their legs between the beams and an angle. The employee suffered two fractured legs.
Employees were replacing a 24" pig trap door. A strap was shackled on the pig trap door and connected to a forklift. Welders began to cut the door off. An employee was holding onto the door when the cut was finished. The door shifted and caught his fingers, resulting in a hand injury and amputation.
An employee used a crane to set down a bar. The bar measured 9 inches by 16 feet. The strap got stuck under the bar, and the employee asked another employee to jog the roll. The bar rolled and pinched the injured employee's left hand, resulting in a fingertip amputation.
More severe injuries in this industry (NAICS 237990)
A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.
An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.
Employees were securing the fuel line of an outboard motor in preparation for removing the motor from a small vessel located in the equipment yard. A gasoline-related fire occurred and one employee sustained burns to both hands and forearms.
A marine diver/construction worker was working underwater, using a hydraulic dredge to clear sediment away from the base of a dam. The dredge's suction nozzle began migrating toward him, and then pulled in his right hand and forearm. He sustained compartment syndrome in the hand and forearm.
An employee was standing on a sheet of -inch by 4-foot by 8-foot plywood on top of a rebar mat, supervising his crew. As he was moving to alert the crew to an incoming overhead load, he stepped off the plywood and his left foot slipped through the rebar mat and landed on the rebar mat below. His left ankle was broken and dislocated.
An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.
An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.
A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.
An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.