Direct exposure to electricity greater than 220 volts · Electrocution, electric shock
At a glance
Federal OSHA recorded a severe workplace injury
at PAR Electrical Contractors, LLC, 7560 Norwood St., PRAIRIE VILLAGE, KANSAS 66208
on — Electrocution, electric shock, affecting the BODY SYSTEMS .
Final narrative
Three employees were responding to a power outage caused by a recent storm. While climbing a utility pole, an employee contacted an electrical component with his left hand, thumb, and index finger, resulting in an electrical shock and probable exposure to an arc flash. The injured employee lost consciousness and was found hanging upside down in his rope harness, requiring resuscitation and resulting in hospitalization.
Hospitalized BODY SYSTEMS Power lines, transformers, convertors
More severe injuries at PAR Electrical Contractors, LLC
An employee was replacing switches on 23-kilovolt circuits at an electrical substation. While trying to take measurements with a metallic tape measure, the employee was shocked and burned.
A crew was changing out a single-phase pole. The injured employee was framing the pole approximately 30 feet from the base. As they were loosening the armor rod clamp, the conductor broke and the wire fell to the ground, landing on the employee's right hand. The employee suffered electrical burns to their right hand and both knees.
An employee (a lineman) was working to restore power by installing a hand line when he contacted a high-voltage device (7,200 volts), resulting in electrical burns to his upper body and hands.
An employee was working from a bucket truck to remove a bolt from an attachment on an energized power line pole. The employee came into contact with the energized phase, resulting in an electrical shock of 7,200 volts. The employee was hospitalized. Protective gloves were not worn at the time of the incident.
On September 29, 2025, an employee was installing a fiber optic line at a residential site. His shoulder contacted the 7,600-kilowatt power line, resulting in an electrical shock. The employee was hospitalized.
Two employees exited their vehicle to assess a fully-downed power pole. The injured employee approached the downed pole to examine it more closely when their feet got caught underneath the energized phase and the ground of the pole, resulting in electrical burns to both feet.
More severe injuries in this industry (NAICS 238210)
An employee was troubleshooting the control setup for a variable air volume box above a ceiling. The employee's hand came into contact with an exposed, energized 277-volt wire that had loosened from its terminal on the box's assembly. He was shocked and fell off a ladder. His left hand passed across the ceiling grid and was lacerated. He also suffered an electrical burn to the right hand and was hospitalized.
An employee was moving a scissor lift through a doorway. The employee was pinned between the scissor lift and the doorframe, sustained a back injury, and was hospitalized.
An employee was standing on an A-frame ladder approximately 6 feet above the floor while he attached a suspended light fixture to the ceiling. The employee lost balance, and fell to the tiled floor below, sustaining blunt force trauma to his head.
An employee was inspecting the overhead area of a single-person lift and repositioning the lift through a double doorway. As they were transitioning through the doorway, they were caught between the doorframe and the vertical mast of the lift. The employee was hospitalized with injuries to the nose, left maxillary sinus, left orbital bone, and left jaw, with fractures at the maxillary sinus area.
The injured employee was performing routine maintenance on a fan belt/pulley. The injured employee and another person were moving the pulley back and forth manually to find a bearing issue. The injured employee's left ring finger got caught between the belt and the pulley wheel, resulting in a soft tissue amputation.
An employee was working to remove a product blockage from a piece of equipment. The employee was struck by a metal bar near the deck of the pin mixer equipment and sustained blunt force trauma to the torso.
An employee was moving a rack onto a lower conveyor in the south heat treat area when their finger got caught between the part tray and the rollers, resulting in a fingertip fracture and amputation.
An employee was climbing a ladder to get on top of the breakroom. The ladder slipped, causing him to fall to the ground. The employee sustained fractures to his upper back, left foot, and ankle.
Two employees were removing a circuit breaker. The injured employee was using wrenches in the removal process. One of the wrenches contacted an adjacent door, resulting in an arc flash. The employee suffered burns to their neck, face, and ear, as well as momentary vision loss due to the flash.
An employee bent over to pick up a rubber mat from the ground. When he grabbed the corner of the mat, a rattlesnake hidden under it bit his left middle finger near the first knuckle. He was hospitalized.