Mueller Copper Tube

An employee was operating an overhead crane to transport a bundle of copper tubing. He went to lower the load as he was approaching a rack, but the suspended bundle of tubing suddenly jerked in the other direction. The bundle struck a nearby tool cabinet, and the cabinet tipped over. The employee went to prevent it from falling. However, the cabinet still fell over, striking his right arm and briefly pinning it against another object. The employee suffered a fractured right forearm that required hospitalization.

An employee was operating a pointer, which reduces the end of copper tubing and allows it to go through a smaller die set to reduce its diameter. It requires two plugs to be set in place to be inserted in the tubing before it can be reduced or pointed. When the machine cycled, the tip of the employee's left thumb was caught by the machine's entry point, severing the tip of the thumb. A partial amputation, which included a small section of bone, was required to repair the injury.

An employee pulled out a bucket of hot oil from under the fryer. The employee then stood on the table to clean the back wall. He stepped down into the bucket of hot oil, resulting in third-degree burns to his left leg.

An employee was performing maintenance under a kettle. When he removed a tri-clamp on a transfer line, the hot fat and broth material in the kettle poured out onto his arm. The employee was hospitalized with burns.

After completing a run with an oil distributor truck, an employee was working to return (suction) the hot oil to the tank of the truck. When the employee opened one of the valves, hot oil (approximately 385 degrees) sprayed their face, resulting in first-, second-, and third-degree burns.

An employee was filtering a fryer with a fryer filter machine. After going around the corner and then returning to the fryers, the employee stepped into the filter machine. The hot oil burned the employee's right ankle, and the employee was hospitalized.

An employee was using a water hose to clean debris out of the outfeed of a log conditioning vat. Water began entering the vat from the adjoining vat through a void in the separation wall at the infeed of the vats. As the employee was exiting the vat he had been working in using the access opening at the outfeed, hot water exiting the access opening entered the top of his protective hip wader. It pooled at the bottom of the wader and burned his left foot and ankle.

An employee was loading an empty reel on the west reel take-up when they noticed that the wire lying on the east reel take-up had over-accumulated on one side of the reel, making it uneven. The employee stopped the east take-up machine and released tension on the wire to correct the lay. As the employee engaged a mechanical rotation function to take up the wire slack, their right little finger was crushed between two separate wire strands on the reel under tension, resulting in a fingertip amputation. The machine was guarded at the time of the incident.

An employee was operating an overhead crane to transport a bundle of copper tubing. He went to lower the load as he was approaching a rack, but the suspended bundle of tubing suddenly jerked in the other direction. The bundle struck a nearby tool cabinet, and the cabinet tipped over. The employee went to prevent it from falling. However, the cabinet still fell over, striking his right arm and briefly pinning it against another object. The employee suffered a fractured right forearm that required hospitalization.

An employee was working to manually clear copper tubes from the turnover rack due to a faulty sensor. As he used his right hand to remove a finished tube from the turnover rack, another tube pushed through the feed line and struck his gloved right ring fingertip. The sharp edge of the copper tube caused a soft tissue amputation to the bottom side of the fingertip.

An employee was working with a drill press when his right glove was caught and pulled into the drill bit. The employee's little fingertip was partially amputated.

An employee was operating equipment to cut a copper pipe (20 feet in length, 2 inches in diameter) when a jam occurred between the revolver assembly and the pinch roller assembly. He assessed the jam and determined that the copper pipe needed to be cut using a battery-powered reciprocating saw. He made two cuts on the pipe with the reciprocating saw. When the second cut was finished, kinetic energy stored within the pipe due to the jam released, and the pipe struck the employee's left hand. The employee's index fingertip was partially amputated before the first knuckle without bone loss.

An employee was checking a pole-type transformer tank for leaks. A hydraulic clamping device was lowered onto his right thumb and crushed it against the sharp edge of the bottom of the tank. He suffered a partial transphalangeal amputation to the thumb.

The injured employee was standing behind a table. She jumped out to scare another employee, but tripped and fell on the tile floor, injuring her right ankle/foot. She was hospitalized with a dislocated ankle that required surgery.

An employee was going into a trailer to mark product for shipment and the trailer pulled away from the dock. The employee fell out of the trailer, contacted the dock plate, and then fell to the ground. The employee was hospitalized with a punctured lung, fractured ribs, and contusions.

An employee was hooking up bundled tie-downs with a chain. While he was holding a hook, the other hook was unlocked. This caused the employee's hook to slide down and pinch his right index finger between the chain and the shackle. He suffered an amputation to the fingertip (without bone loss), as well as an open fracture.

An employee was operating a gas tugger to lift metal sheeting. His left hand was pulled into the pulley, which crushed his left thumb, resulting in avulsions and other tissue damage. He was hospitalized and required surgery.