Wanzek Construction, Inc.

A crew was working on assembling/disassembling a crawler crane. The injured employee was removing the becket pin from the crane block. When the pin came out of the hole, the becket dropped onto his right middle fingertip, resulting in amputation.

An employee dropped a bolt which then went into a small hole. The employee reached down to retrieve the bolt and was bitten by an Eastern cottonmouth snake. The employee was hospitalized.

Employees were aligning an electrical cabinet on a deck inside the entrance to a wind turbine. They were using a come-along, connected to an anchor at the base of the tower, to position the cabinet at the center of the tower. While an employee was checking for proper positioning, the cabinet moved toward the tower wall and his right index finger was caught in the 1/2-inch gap between them. The fingertip was amputated.

An employee developed heat illness at a wind turbine erection work site. The employee was hospitalized, suffering from heat-related muscle injury.

At 8:30 p.m. on June 7, 2022, an employee became ill while working with a crew to adjust solar dampeners. He was hospitalized that afternoon for heat illness and a heat-related muscle injury. On the day before, he was installing dampeners for 10 hours and experienced symptoms of heat illness.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

An employee was checking a pole-type transformer tank for leaks. A hydraulic clamping device was lowered onto his right thumb and crushed it against the sharp edge of the bottom of the tank. He suffered a partial transphalangeal amputation to the thumb.

An employee had been cleaning the work area. While lifting a saw, the employee's index finger was lacerated by the saw blade. A tendon was cut and required surgery.

An employee was installing a hydraulic extension cylinder in a tow truck when their leg was caught between the cylinder and the truck frame. The employee was hospitalized with a broken tibia, which required surgery.

An employee was sorting sucker rods. His right hand was caught in the area where the rod hits up against the frame and his index fingertip was amputated just below the nail.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.

Employees were securing the fuel line of an outboard motor in preparation for removing the motor from a small vessel located in the equipment yard. A gasoline-related fire occurred and one employee sustained burns to both hands and forearms.

A marine diver/construction worker was working underwater, using a hydraulic dredge to clear sediment away from the base of a dam. The dredge's suction nozzle began migrating toward him, and then pulled in his right hand and forearm. He sustained compartment syndrome in the hand and forearm.

An employee was standing on a sheet of -inch by 4-foot by 8-foot plywood on top of a rebar mat, supervising his crew. As he was moving to alert the crew to an incoming overhead load, he stepped off the plywood and his left foot slipped through the rebar mat and landed on the rebar mat below. His left ankle was broken and dislocated.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.