Struck by suspended or swinging objects n.e.c. · Multiple severe wounds and internal injuries
At a glance
Federal OSHA recorded a severe workplace injury
at SMS Group Inc, 1303 East Count Road 876, OSCEOLA, ARKANSAS 72370
on — Multiple severe wounds and internal injuries, affecting the Multiple trunk locations.
Final narrative
Two employees were loading a roll into an EDT machine. One employee was operating the crane and the other employee was the EDT operator. The crane operator was between the roll and the EDT machine. Both employees were struck by the suspended roll and knocked into the EDT machine wall. Both employees sustained internal abdominal injuries requiring surgery and hospitalization. One employee was fatally injured.
On October 26, 2024, employees were preparing to clean a parts washer. An employee went up the stairs and stepped off the platform onto the door frame. They then stepped onto the washer's table to connect an overhead crane to the cleaned parts basket. They walked back across the washer's table to exit and then stepped back onto the door frame with their right foot to reach the step platform. Their left foot slipped and was submerged approximately 6-7 inches in an uncovered water reservoir containing water heated to approximately 170 F. The employee sustained second-degree burns on their left ankle and foot.
An employee was walking into the motor control center (MCC) room when his right ring finger was caught in the hinge of a doorway. He sustained an open phalanx fracture, which resulted in a partial amputation above the first knuckle.
An employee was stacking concrete blocks for a concrete bunker. As a block was swinging into place, the employee's left leg was pinched between two blocks, resulting in injuries to his left heel and lower leg.
An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.
An employee was placing a board on top of a bundle of steel tubing. A crane was moving a bundle of steel that struck the employee and caught them against another bundle of steel tubing. The employee sustained a crushing injury and hematoma to the right upper leg.
Employees were using a crane to lower large tree stems and branches while removing limbs and branches from the load. This caused the load to shift and strike an employee in the back, resulting in a hematoma on the lower left part of their back and a fractured ankle.
More severe injuries in this industry (NAICS 331221)
An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.
An employee was removing a roll (tooling) from a machine when their left little finger was pinched between the roll and the machine, resulting in a partial amputation.
An employee was rolling a piece of steel in the belt of a shape roller machine when his finger was pinched between two pieces of steel. His right ring and middle fingers were amputated.
An employee was cutting a length of steel coil when he noticed the steel might have cross-break defects. He used his gloved hand to feel for and clean the defected spots when his glove got caught in the measuring wheel, which rolls along the top of the steel to ensure accurate cuts. The employee's arm was pulled down into the machine until his body was stopped by a support bar that goes across the machine. The employee's arm was fractured at the elbow and required hospitalization.
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.