CARGILL MEAT SOLUTIONS

An employee was in the basement when he observed animal blood dripping from a small hole in the auger trough. The employee went to plug the hole with a small piece of fat. As the employee pushed the fat into the hole, the auger flight caught his fingertip, resulting in amputation between the nailbed and first knuckle.

An employee was operating a band saw and sustained a partial amputation to their right index fingertip.

An employee was removing scraps of meat from underneath a barrel dumper when she was struck by the barrel dumper, resulting in pelvic fractures.

An employee was pushing a piece table when it struck a machine. The employee's finger was pinched and partially amputated between the table and machine.

An employee was driving a forklift when it collided with another forklift. The employee's middle finger was pinched between the two forklifts and partially amputated.

An employee was assisting with pipe on a drilling rig. The slips came down and landed on the employee's left foot fracturing four metatarsals.

Two employees were struck by the rotary table of a drilling rig while installing caisson. Employee 1 suffered multiple fractures, internal injuries, and head trauma. Employee 2 suffered multiple fractures, internal injuries, spinal injury, and head trauma.

Employees were felling hazard trees. The injured employee was conducting 'bucking' operations to saw a tree from the road when the tree kicked-back, pinning him against the ground and fracturing his left femur. The employee was hospitalized and required surgery.

An employee was greasing tongs on a work-over rig. The tongs lacerated one of the employee's fingers.

An employee was chaining a vehicle when he had to change tools and the compressor. As the compressor was being charged, the employee stepped near the vehicle to make sure the compressor was attached. Then, he instructed a co-worker to lower the compressor. His right hand was on the compressor and under the chain, causing his ring finger to be crushed.

An employee was scraping dried glue from the top lid of a hot glue pot. His left hand slipped and came into contact with the hot glue. He then suffered burns to his hands and fingers as he tried to remove the glue. He was hospitalized.

An employee was in a scissor lift approximately 20 feet above the ground to place a plastic tarp on a catwalk in order to catch condensation. They positioned the lift opposite the work area and stepped out of the scissor lift onto an I-beam. The employee fell from the I-beam to the ground. The employee was hospitalized with a skull fracture on the right side of their head and injuries to the chest and both eyes.

A maintenance employee was called to look at a pallet conveyor machine where a chain had fallen off a sprocket wheel. When the employee grabbed the loose chain, a light sensor caused the machine to restart. This created a pinch point between the chain and sprocket that caught the employee's left little finger. The finger was surgically amputated at the second knuckle.

The injured employee was standing by one of the stationary computers along the wall. There was a half-pallet located approximately 3 feet behind the employee that consisted of 12-pound boxes stacked six boxes high. A forklift was transporting a pallet that came in contact with the stationary pallet behind the injured employee, causing four boxes to fall and contact their legs. The injured employee was hospitalized with leg injuries.

An employee was using a box strapping machine to place straps on boxes when his right middle finger was caught in the machine, resulting in an open fracture to the distal phalanx.

An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.

An employee was cutting cabinet trim using a table saw when four fingers on his left hand were severed, resulting in hospitalization and amputation.

An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.

A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.