Nonroadway collision with other vehicle, unspecified · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at Vestas Nacelles America, Inc., 1500 E. Crown prince Blvd., BRIGHTON, COLORADO 80603
on — Fractures, affecting the multiple body parts, n.e.c..
Final narrative
An employee was counting inventory while riding a lift when the vehicle struck the forks of an upright forklift working in the same area. He fell approximately 19 feet with the lift basket and struck the concrete below, breaking his upper right arm, pelvis, and left leg. He was wearing fall protection at the time.
HospitalizedMultiple body parts, n.e.c.Aerial lifts, scissor lifts-except truck-mounted
More severe injuries at Vestas Nacelles America, Inc.
An employee was screwing a nut onto a bolt using a battery-powered torque tool when their left index fingertip was pinched between the tool and the bolt. The fingertip was amputated.
An employee was driving a forklift when it collided with another forklift. The employee's middle finger was pinched between the two forklifts and partially amputated.
A temporary employee was operating a powered industrial truck and attempting to maneuver around another automated powered industrial truck when the vehicles collided. The employee sustained a crush injury to their right foot.
An employee was operating a double pallet jack down an aisle when he was struck by another double pallet jack. The employee's right lower leg was then caught between the pallet jack and a rack beam, resulting in an injury just above the right ankle that required hospitalization.
An employee was operating a ride-on double pallet jack when he was struck from behind by another pallet jack. Their lower right leg was caught resulting in fractures to the tibia and fibula.
More severe injuries in this industry (NAICS 423830)
An employee was sorting sucker rods. His right hand was caught in the area where the rod hits up against the frame and his index fingertip was amputated just below the nail.
An employee was using a powered miter saw to cut 2x4's. The saw blade hit something inside a board (possibly a hidden nail) and jumped, causing a laceration to the employee's left forearm. The employee was hospitalized with soft tissue and tendon injuries that required surgery.
A crane had been used to set a steel plate on a steel frame. An employee was trying to remove a clamp from the plate when the plate fell and crushed the tip of his left little finger. The employee sustained a fingertip amputation.
An employee was operating a scissor lift, raised to a height of about 15 feet, to inspect an overhead crane rail. The crane itself was being moved. Its hook swung into the scissor lift s arms, causing the lift to tip over onto its side, which in turn caused the lift and the employee to fall to the floor. The employee suffered injuries including broken ribs, spinal fractures, scapula fractures, and internal injuries.
A technician was operating a crane hoist to lift/remove a cylinder head from the main engine (port). The load was lifted at an angle, causing the cylinder head to get stuck on the cylinder head studs. When it became free from the studs, the cylinder head swung. It struck the technician and caught them against the cabinet door. This resulted in an amputation of their left index fingertip at the distal knuckle.
An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.
An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.
A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.
An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.