Ignition of vapors, gases, or liquids · Second degree electrical burns
At a glance
Federal OSHA recorded a severe workplace injury
at Tolin Mechanical Systems Company, 420 S Rush Road, RUSH, COLORADO 80833
on — Second degree electrical burns, affecting the hand(s) and wrist(s).
Watch Tolin Mechanical Systems Company — freeGet an email when a new federal OSHA severe-injury report for Tolin Mechanical Systems Company is published. One employer, no account, unsubscribe in one click.
Final narrative
An employee was working on an electrical component of the water pump when the lead contacts sparked. The sparks ignited an unknown gas that was coming from a capped well in the work area. The employee was engulfed in flames and sustained first and second degree burns to both hands and wrists and first degree burns to his face.
HospitalizedHand(s) and wrist(s)Chemicals and chemical products, unspecified
More severe injuries at Tolin Mechanical Systems Company
At 11:05 a.m., an employee was retrieving screws and a duct puller from their van at a jobsite. After getting the materials, they closed the side door and locked it, and then began to head back to the work area. They then stepped on a sprinkler pipe approximately 14 inches away from the side of their vehicle. The employee fell to the ground and suffered a broken right fibula and tibia, resulting in hospitalization.
An employee was on-site performing scheduled preventative maintenance tasks in the building. He was attempting to break a pipe union on an external rear blow-down line to check it for obstructions when scalding water spontaneously released from inside the boiler and exited the pipe cleanout port, which had its cap removed. He sustained first, second, and third degree burns on his legs, the right side of his torso, and his right arm.
An employee was cleaning a cordless drill. As they applied brake fluid to the drill and pulled the trigger, the fluid ignited. The employee suffered burns to the face, hands, and arms.
An employee was spraying glue to the floor of an enclosed cargo trailer. The fumes made contact with the heater causing a flash fire. The employee suffered burns to their face and right hand.
An employee was replacing a valve in the gas line to the fryer. The shutoff valve malfunctioned resulting in a gas leak that then ignited. The employee sustained burns requiring hospitalization.
An employee was moving a 3-ton condensing unit, strapped down on a dolly, out of a garage. The strap broke, causing the employee to fall backward onto the brick pavered driveway. The employee suffered injury to a spinal ligament in the neck.
An employee was closing the side cargo door to a company van. The tip of his finger got caught between the door and the door jamb, resulting in a partial amputation.
While working at a customer's residence, an employee was cutting tape with a box cutter to wrap insulation for a piece of pipe. The box cutter struck a hardened object within the wall causing it to bounce back and puncture the employee's right eye. The employee was hospitalized.
An employee was assembling a baker type scaffold. He was beginning to transverse down the scaffold, approximately six feet off the ground, when the scaffold tipped over and he fell. The employee was hospitalized with a fractured femur.
An employee was trimming out sprinklers on the exterior of a building when he fell off an extension ladder. He landed on the ground and sustained fractures to his nose and arm.
An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.
An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.
A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.
An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.