AECOM

An AECOM maintenance employee was troubleshooting a malfunctioning encoder device. To access the device, the employee had to stand on top of a tank holding a caustic cleaning solution, about 3 feet off the ground. The employee's left leg slipped through one of the access covers and was immersed in the caustic solution up to the knee. The employee suffered third-degree burns to the lower leg.

An employee was welding on a newly fabricated fuel tank when a flash fire occurred. Residual fumes in the tank ignited and flames exited the tank opening, causing burns to the employee's face and chest.

An aircraft mechanic was conducting maintenance on an aircraft from the ground. When he extended a boarding ladder, which is built into the aircraft, his left thumb was caught in pinch points and amputated from the nail to the knuckle.

An employee fell when a rail broke, landing on the asphalt ground. The employee suffered fractures and was hospitalized.

An aircraft mechanic was working on the left wing of an F-18 aircraft removing a component section of the wing known as a flight control surface. During this process the employee pushed on a bolt with his finger. When the bolt moved, the employee's right index finger followed and was caught in a pinch point by the weight of the falling component. The fingertip was amputated.

An employee was transporting a container across the street to the trash truck when he was struck by a vehicle. He sustained lower back bruising, a left leg fracture, and a laceration to the back of his head.

An employee was in the middle of a roundabout when they were struck by a vehicle, resulting in injuries to their head, neck, back, hips and legs.

An employee was walking from the car to get to work when they were struck by a motor vehicle on an access road. The employee sustained a left ankle fracture and head bruising.

An employee was leaving their vehicle to place cones on the street for traffic control. A car struck the employee, who suffered a broken cheekbone. The employee was hospitalized.

After cleaning the sidewalks on one side of a street, an employee was crossing the street to clean the sidewalk on the other side. A car struck him, and he suffered a head injury.

An employee was working to free a load by grabbing and shaking the live side of a tugger line. Once the load became free and progressed upward, the employee's hand was caught and pulled into a snatch block. The employee's right thumb was broken and lacerated. The employee was hospitalized and required a surgical amputation.

An employee was operating a drill rig when when their hand got caught between a 1/4-inch steel cable and a drill rod, resulting in the amputation of four fingers.

An employee was overseeing the operation of a rope being respooled onto the drum of a wire winding machine. He went to remove a piece of wooden reel from the rope. His glove got snagged and his right hand was pulled into the roller, pinching his fingers between the machine's roller and the rope. The middle and index fingers were crushed.

An employee was visiting a patient's home to fit them with a wearable cardiac defibrillator. As he was walking from the front door to his car, a large dog broke free from a chain and attacked him. He was bitten on the forearm and fell. The patient was then able to restrain the dog. The employee was hospitalized with severe dog bites and required surgery.

An employee tripped over a junior I-beam about 4 feet long and 6 inches tall that was installed for circulating water valves and fell to the ground, resulting in a broken right-side rib.

An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.

An employee was cutting cabinet trim using a table saw when four fingers on his left hand were severed, resulting in hospitalization and amputation.

An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.

A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.