Thompson Pipe Group

An employee was anchored to a movable piece of equipment called a "lid" with a self-retracting lifeline harness. An overhead crane lifted the equipment, causing the employee to be pulled by his harness. The employee was pulled off the walkway and swung over the wall of the kiln. His body and head struck the wall. The employee lost consciousness and sustained a laceration to the side of his head that required stitches. The employee also sustained multiple fractured ribs and fractured vertebrae.

An employee was standing on the mill, by the cross-seam area, preparing to open a bag of flux to pour into the hopper. The machine's holding clamps engaged and the clamp crushed the employee's left foot pushing the steel toe protection plate into their left toe.

An employee was helping to hoist a pipe. The pipe swung and the employee's finger was caught between it and a beam. He suffered an amputation to the left middle finger.

An employee was operating a paint machine when the pistons became stuck, so he applied lubricant oil to make them come loose. He was cleaning near the piston by hand when the piston suddenly came loose and caught the his right index fingertip, amputating it.

An employee was grabbing the end ring of a pipe to move it when his right hand was caught between that ring and a second metal ring, partially amputating his right middle finger.

An employee was assisting with pipe on a drilling rig. The slips came down and landed on the employee's left foot fracturing four metatarsals.

Two employees were struck by the rotary table of a drilling rig while installing caisson. Employee 1 suffered multiple fractures, internal injuries, and head trauma. Employee 2 suffered multiple fractures, internal injuries, spinal injury, and head trauma.

Employees were felling hazard trees. The injured employee was conducting 'bucking' operations to saw a tree from the road when the tree kicked-back, pinning him against the ground and fracturing his left femur. The employee was hospitalized and required surgery.

An employee was greasing tongs on a work-over rig. The tongs lacerated one of the employee's fingers.

An employee was chaining a vehicle when he had to change tools and the compressor. As the compressor was being charged, the employee stepped near the vehicle to make sure the compressor was attached. Then, he instructed a co-worker to lower the compressor. His right hand was on the compressor and under the chain, causing his ring finger to be crushed.

An employee was anchored to a movable piece of equipment called a "lid" with a self-retracting lifeline harness. An overhead crane lifted the equipment, causing the employee to be pulled by his harness. The employee was pulled off the walkway and swung over the wall of the kiln. His body and head struck the wall. The employee lost consciousness and sustained a laceration to the side of his head that required stitches. The employee also sustained multiple fractured ribs and fractured vertebrae.

An employee was using an overhead crane to lower a manhole cylinder to the ground to complete maintenance and cleaning. While removing a lifting hood from a manhole core (steel cylinder), the cylinder rolled and the employee's left little finger was caught between the crane hook and the lifting eye. The employee's little fingertip was amputated just below the nail.

An employee was moving a 4x4 box jacket with an overhead crane. The employee hooked a chain to the jacket and put tension on it. It spun awkwardly, striking the employee and knocking him over. The employee fell on the same level and sustained a fractured rib and lacerations to his lower left abdomen and backside.

An employee was guiding a forklift operator who was placing a 48-inch form jacket (open cylinder) over a core (solid, stationary cylinder). The employee was positioned on the ground adjacent to the core. As the suspended jacket was positioned over the core, a gust of wind caused the jacket to move. The employee reached to steady it and the jacket moved downward pinching his left little finger between the jacket and the core and resulting in a fingertip amputation.

An employee was at the bell packer when the scraper of the bell packer struck his hand. The employee sustained broken fingers and degloving injuries involving their right ring and little fingers.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.