Struck by suspended or swinging objects n.e.c. · Amputations, avulsions, enucleations unspecified
At a glance
Federal OSHA recorded a severe workplace injury
at Forterra Concrete Products, Inc., 1601 Culvert Street, RAPID CITY, SOUTH DAKOTA 57701
on — Amputations, avulsions, enucleations unspecified, affecting the Finger or thumb tip(s), nail(s).
Final narrative
An employee was guiding a forklift operator who was placing a 48-inch form jacket (open cylinder) over a core (solid, stationary cylinder). The employee was positioned on the ground adjacent to the core. As the suspended jacket was positioned over the core, a gust of wind caused the jacket to move. The employee reached to steady it and the jacket moved downward pinching his left little finger between the jacket and the core and resulting in a fingertip amputation.
Amputation Finger or thumb tip(s), nail(s) Structural elements n.e.c.
More severe injuries at Forterra Concrete Products, Inc.
An employee was bending 3-foot long rebar on a rebar bending machine. He was bending to 90-degree angles, using the foot pedal for control. His finger was caught in a pinch point and was partially amputated.
An employee was walking into the motor control center (MCC) room when his right ring finger was caught in the hinge of a doorway. He sustained an open phalanx fracture, which resulted in a partial amputation above the first knuckle.
An employee was stacking concrete blocks for a concrete bunker. As a block was swinging into place, the employee's left leg was pinched between two blocks, resulting in injuries to his left heel and lower leg.
An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.
An employee was placing a board on top of a bundle of steel tubing. A crane was moving a bundle of steel that struck the employee and caught them against another bundle of steel tubing. The employee sustained a crushing injury and hematoma to the right upper leg.
Employees were using a crane to lower large tree stems and branches while removing limbs and branches from the load. This caused the load to shift and strike an employee in the back, resulting in a hematoma on the lower left part of their back and a fractured ankle.
More severe injuries in this industry (NAICS 327332)
An employee was anchored to a movable piece of equipment called a "lid" with a self-retracting lifeline harness. An overhead crane lifted the equipment, causing the employee to be pulled by his harness. The employee was pulled off the walkway and swung over the wall of the kiln. His body and head struck the wall. The employee lost consciousness and sustained a laceration to the side of his head that required stitches. The employee also sustained multiple fractured ribs and fractured vertebrae.
An employee was using an overhead crane to lower a manhole cylinder to the ground to complete maintenance and cleaning. While removing a lifting hood from a manhole core (steel cylinder), the cylinder rolled and the employee's left little finger was caught between the crane hook and the lifting eye. The employee's little fingertip was amputated just below the nail.
An employee was moving a 4x4 box jacket with an overhead crane. The employee hooked a chain to the jacket and put tension on it. It spun awkwardly, striking the employee and knocking him over. The employee fell on the same level and sustained a fractured rib and lacerations to his lower left abdomen and backside.
An employee was at the bell packer when the scraper of the bell packer struck his hand. The employee sustained broken fingers and degloving injuries involving their right ring and little fingers.
An employee was cleaning out a mixer lid when a hatch fell from its open position and severed the tip of his left thumb. The employee sustained a partial amputation of the tip of their left thumb.
An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.
An employee was walking past a crossover conveyor when a ramp came down and hit them in the back. The employee sustained a broken back vertebra, as well as a concussion, and was hospitalized.
An employee was using a hook tool to pull a pallet onto the lift gate of a tractor trailer. The hook detached from the underside of the pallet, causing the employee to fall backward off the lift gate. The employee landed on the concrete parking lot about 5 feet below, suffering fractures to the skull and two thoracic vertebrae.
An employee was walking on a truss table when he lost his balance and fell approximately 3 feet to the floor. The employee sustained a dislocated and fractured left ankle.