Federal OSHA recorded a severe workplace injury
at FasCast Inc., 6107 W. 71st South Ave., TULSA, OKLAHOMA 74131
on — Fractures, affecting the lower leg(s).
Final narrative
An employee was grinding down a casting when the grinding wheel exploded, striking and cutting his left leg. He fell backward and broke his tibia in two places. He was hospitalized, undergoing surgery.
A temporary employee was cutting a pipe with a saw. The saw blade bound up, kicked back, and hit the employee's foot just behind the steel toe, cutting the big toe at the joint and severing a tendon. He was hospitalized.
An employee came inside to warm himself next to a lit ladle (a drying process in an open flame pit), causing his shirt to catch fire. The employee sustained burns to his back.
An employee was standing on the rail of the mega mixer. The employee was crossing over the rails and slipped. The employee's right foot was struck by the mega mixer and pinned between the wheel and rail.
An employee was loading a dish washing machine. A plate bumped against the machine and broke, lacerating the employee's left arm. The employee was hospitalized and required surgery.
Two Rycon employees were installing glass marker boards in a nearly completed space. Each employee had a suction cup on the face of the board and a hand on the bottom of the board. Upon hanging the third board in sequence on a hang strip mounted to the wall, the board needed to be moved about half an inch to butt tightly to the adjacent one. When the employees moved the marker board, it shattered causing half of the board to fall and cause a severe laceration to an employee's left wrist.
On May 15, 2023, an employee removed a mirror from the bathroom to discard it. As the employee went to place it on the cart, the mirror broke. The employee sustained a laceration on the right forearm that required surgery.
An employee was lifting a round, glass table top while working on a waste collection route. The glass table top shattered and lacerated the employee's arm.
More severe injuries in this industry (NAICS 331511)
An employee was realigning two halves of a core box on a core-making machine. Pneumatic pressure released, causing the core box to close on the employee's right thumb. The thumb tip was amputated between the nail and the knuckle.
An employee was performing maintenance/electrical work inside a substation, and used a ladder to access the top of a panel box. The employee fell 8-9 feet from the top of the panel box to the ground. The employee was hospitalized with fractures to their ribs and a shoulder injury.
An employee's hand was caught in a pinch point in the area of a conveyor for a flask running out of a foundry molding machine. The employee's ring finger was crushed and partially amputated at the base.
An employee noticed a block was out of place under the weighted mold frame. The employee used another block to push the block out and replace it. When the block came out, the frame came down on his right ring and little fingers. The employee sustained a fracture and partial amputation to the ring fingertip.
An employee was using a fork truck to move a tub containing molten iron that had been drained from the cupula. The tub tipped over and the molten metal came in contact with water. This caused the molten iron to splash back and burn the employee's upper torso.
An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.
An employee was working in the food service warehouse when he experienced chest pain, difficulty breathing, and lost consciousness. The employee sustained carbon monoxide poisoning.
An employee was cutting a piece of metal rod with a metal cutting machine. His right middle finger became caught between the rod and the machine's table. The employee's fingertip was partially amputated.
An employee was working at her desk. She went to stand up and fell to the floor beside the desk. The employee sustained a hip displacement and required surgery.
An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.