Struck by running powered equipment irregular movement, kick back · Cuts, lacerations, punctures without injury to internal structures
At a glance
Federal OSHA recorded a severe workplace injury
at FasCast Inc., 6107 W 71st St, TULSA, OKLAHOMA 74131
on — Cuts, lacerations, punctures without injury to internal structures, affecting the Foot (feet), toe(s) unspecified.
Final narrative
A temporary employee was cutting a pipe with a saw. The saw blade bound up, kicked back, and hit the employee's foot just behind the steel toe, cutting the big toe at the joint and severing a tendon. He was hospitalized.
An employee came inside to warm himself next to a lit ladle (a drying process in an open flame pit), causing his shirt to catch fire. The employee sustained burns to his back.
An employee was grinding down a casting when the grinding wheel exploded, striking and cutting his left leg. He fell backward and broke his tibia in two places. He was hospitalized, undergoing surgery.
An employee was standing on the rail of the mega mixer. The employee was crossing over the rails and slipped. The employee's right foot was struck by the mega mixer and pinned between the wheel and rail.
An employee was cutting a board using a circular saw. The saw pinched, kicked back, and cut the employee's left ring and little fingers. The employee suffered an amputation to the little finger.
An employee was cutting wood with a circular saw. The saw kicked back, and its blade cut three fingers on the employee's right hand, resulting in an amputation.
An employee was doing a cutback on a piece of lumber using a chop saw. The saw hit a knot, the piece of lumber buckled, then kicked back and broke the kickback guard. The board was then pulled back into the blade, which lacerated the employee's left index and middle fingers.
An employee was cutting wood with a circular saw. The machine lagged and cut the employee's finger. The employee required surgical amputation of the finger at the hospital.
More severe injuries in this industry (NAICS 331511)
An employee was realigning two halves of a core box on a core-making machine. Pneumatic pressure released, causing the core box to close on the employee's right thumb. The thumb tip was amputated between the nail and the knuckle.
An employee was performing maintenance/electrical work inside a substation, and used a ladder to access the top of a panel box. The employee fell 8-9 feet from the top of the panel box to the ground. The employee was hospitalized with fractures to their ribs and a shoulder injury.
An employee's hand was caught in a pinch point in the area of a conveyor for a flask running out of a foundry molding machine. The employee's ring finger was crushed and partially amputated at the base.
An employee noticed a block was out of place under the weighted mold frame. The employee used another block to push the block out and replace it. When the block came out, the frame came down on his right ring and little fingers. The employee sustained a fracture and partial amputation to the ring fingertip.
An employee was using a fork truck to move a tub containing molten iron that had been drained from the cupula. The tub tipped over and the molten metal came in contact with water. This caused the molten iron to splash back and burn the employee's upper torso.
An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.
An employee was working in the food service warehouse when he experienced chest pain, difficulty breathing, and lost consciousness. The employee sustained carbon monoxide poisoning.
An employee was cutting a piece of metal rod with a metal cutting machine. His right middle finger became caught between the rod and the machine's table. The employee's fingertip was partially amputated.
An employee was working at her desk. She went to stand up and fell to the floor beside the desk. The employee sustained a hip displacement and required surgery.
An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.