Struck by object falling from vehicle or machinery-other than vehicle part · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at Electric Boat, 75 Eastern Point Road, GROTON, CONNECTICUT 06340
on — Fractures, affecting the leg(s), unspecified.
Final narrative
A 6-foot piece of steel weighing approximately 1,300 pounds was being hoisted, when it slipped from the rigging and fell from approximately 8 feet, striking a machine and then striking an employee in the leg. The employee's leg was fractured.
HospitalizedLeg(s), unspecifiedStructural metal materials, unspecified
A painter working in the sonar dome of a submarine was power washing in a confined space when they fell three levels (approximately 20 feet) through a 2' x 4' access hole. The employee lost consciousness and suffered a contusion to the back of the head and pneumonia from inhaled water.
After performing a welding operation inside of a tank, an employee was exiting the tank when his leg caused a welding lead to short against the side of the tank and an electric arc occurred. His leg was burned, requiring hospitalization.
An employee had put a pipe in a vise and was adjusting the flange to insert a ring into the unit. The unit slipped from the vise; as the pipe fell and the employee tried to grab it, the vise pinched the employee's finger. He suffered a fingertip amputation on his left hand.
An employee was adjusting a vice on a drill press table when the device shifted, causing his left pinky finger to become caught between the key slot and the fixture. A chunk of flesh was removed.
An employee was transporting an 800-pound die on a cart from the tool room. The employee was pulling the cart when it struck a metal plate on the floor. This caused the cart to tip forward and the die to slide off the cart. The die struck the employee's left foot and their second toe was amputated.
An employee was using a forklift to load pallets of product on a trailer. He exited the forklift to adjust a pallet by hand. The pallet fell on him, resulting in an injury to the left leg.
An employee was lifting a 500-pound steel counterweight off a pallet using a magnetic hold jib crane. The counterweight detached from the crane and the employee sustained a left foot/toe fracture that required surgery.
An employee was using a pipe wrench to turn a 42-foot-long steel pipe on jack stands to weld the bottom portion. The pipe fell off the stands, striking the injured employee on his left shin. The employee sustained a left leg fracture at the shin area as well as a tibia fracture that required surgery.
More severe injuries in this industry (NAICS 336611)
An employee was hooking up bundled tie-downs with a chain. While he was holding a hook, the other hook was unlocked. This caused the employee's hook to slide down and pinch his right index finger between the chain and the shackle. He suffered an amputation to the fingertip (without bone loss), as well as an open fracture.
An employee was preparing to bend a flat bar in a brake press. When the machine was jogged, the stock rotated up and crushed his left middle fingertip against the outer frame of the die. The fingertip was amputated.
An employee was cutting metal with a torch. A piece of metal struck the employee's left foot, causing multiple fractures to metatarsal(s). The employee was hospitalized.
An employee was descending a ladder carrying a bag of trash. He fell, landed on the ground about 10 feet below, and suffered fractures to his right hip and pelvis.
An employee was checking on a machine outside of the building and removed a cover to clean out a blocked area. His hand was caught by a rotary valve in a dust collection machine. The employee's fingertip was amputated.
An employee was working to clean a glue roller with a scraper tool. The tool and the employee's left thumb were pinched between two rollers, resulting in a partial amputation.
An employee was re-arranging boxes of pipe insulation on a pallet. One of the boxes fell from the pallet and knocked over an upright empty cylinder. The cylinder fell and crushed the tip of the employee's right toe. The employee's toe required surgical amputation.
An employee was securing the claw of a grapple truck to the truck bed. His left little finger was caught between the tie down strap and the rub rail of the truck, resulting in partial amputation of the finger.
An employee was cutting extruded aluminum framing material using a horizontal band saw. She went to grab a rag in the machine when the rag contacted the blade and pulled her hand in toward the blade, resulting in a partial amputation of the right index finger.