ELECTRIC BOAT

A 6-foot piece of steel weighing approximately 1,300 pounds was being hoisted, when it slipped from the rigging and fell from approximately 8 feet, striking a machine and then striking an employee in the leg. The employee's leg was fractured.

A painter working in the sonar dome of a submarine was power washing in a confined space when they fell three levels (approximately 20 feet) through a 2' x 4' access hole. The employee lost consciousness and suffered a contusion to the back of the head and pneumonia from inhaled water.

After performing a welding operation inside of a tank, an employee was exiting the tank when his leg caused a welding lead to short against the side of the tank and an electric arc occurred. His leg was burned, requiring hospitalization.

An employee had put a pipe in a vise and was adjusting the flange to insert a ring into the unit. The unit slipped from the vise; as the pipe fell and the employee tried to grab it, the vise pinched the employee's finger. He suffered a fingertip amputation on his left hand.

An employee was adjusting a vice on a drill press table when the device shifted, causing his left pinky finger to become caught between the key slot and the fixture. A chunk of flesh was removed.

An employee was installing a 15-amp breaker in an electrical panel when a 12-gauge ground wire touched the positive busbar of the panel, resulting in an arc flash. The employee sustained a second-degree burn to their left hand.

An employee was repairing an HVAC system in the drop tile ceiling of a conference room when they were shocked, causing them to fall from the ladder. The employee sustained burns to their right middle and ring fingers.

An employee was replacing a contactor inside an electrical panel attached directly to a press. The press itself was receiving power from another main panel. After replacing the contactor, the employee flipped the switch and an arc flash occurred, burning the employee's elbow, bicep, and neck.

An employee was attempting to switch a medium-voltage primary cable and install a 200-amp fuse barrel. The employee contacted the bottom of the switch gear cradle for the fuse barrel, causing an arc blast. The electricity entered the employee s left hand and exited his big toes, resulting in electric shock and burns to the left hand, arm, shoulder, and both feet. The employee was hospitalized.

On December 6, 2023, an employee of Duke Energy was working on a single-phase 120-/240-volt parallel service re-tap when a secondary flash occurred in an underground service. The employee suffered a second-degree burn to the face and was hospitalized.

An employee was hooking up bundled tie-downs with a chain. While he was holding a hook, the other hook was unlocked. This caused the employee's hook to slide down and pinch his right index finger between the chain and the shackle. He suffered an amputation to the fingertip (without bone loss), as well as an open fracture.

An employee was struck by a plasma cutter and suffered a broken left tibia and fibula. The employee was hospitalized.

An employee was preparing to bend a flat bar in a brake press. When the machine was jogged, the stock rotated up and crushed his left middle fingertip against the outer frame of the die. The fingertip was amputated.

An employee was cutting metal with a torch. A piece of metal struck the employee's left foot, causing multiple fractures to metatarsal(s). The employee was hospitalized.

An employee was descending a ladder carrying a bag of trash. He fell, landed on the ground about 10 feet below, and suffered fractures to his right hip and pelvis.

An employee was checking on a machine outside of the building and removed a cover to clean out a blocked area. His hand was caught by a rotary valve in a dust collection machine. The employee's fingertip was amputated.

An employee was working to clean a glue roller with a scraper tool. The tool and the employee's left thumb were pinched between two rollers, resulting in a partial amputation.

An employee was re-arranging boxes of pipe insulation on a pallet. One of the boxes fell from the pallet and knocked over an upright empty cylinder. The cylinder fell and crushed the tip of the employee's right toe. The employee's toe required surgical amputation.

An employee was securing the claw of a grapple truck to the truck bed. His left little finger was caught between the tie down strap and the rub rail of the truck, resulting in partial amputation of the finger.

An employee was cutting extruded aluminum framing material using a horizontal band saw. She went to grab a rag in the machine when the rag contacted the blade and pulled her hand in toward the blade, resulting in a partial amputation of the right index finger.