Caught in running equipment or machinery during maintenance, cleaning · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at Futamura USA, Inc., 6000 SE 2nd St, TECUMSEH, KANSAS 66542
on — Fractures, affecting the arm(s), unspecified.
Final narrative
An employee working as a finishing operator was using sand paper to clean a spindle roll on a slitter machine. The employee's arm was caught in the spinning rollers. The employee sustained a compound fracture to the right arm requiring hospitalization and surgery.
HospitalizedArm(s), unspecifiedSpecial process machinery, unspecified
An employee was operating a stand-up forklift to move a pallet of product that was sitting on the floor in an aisle of the finishing warehouse next to metal racking. The forklift cab went under the middle shelf and his torso became caught between the metal shelf (at his back) and the forklift steering control stick (at his front). He was hospitalized with possible fractured ribs.
An employee was kneeling on the padded work platform of a casting machine, reaching to pull slack out of a film web being re-threaded through the machine. He lost his balance and slipped, and his right hand, wrist, and forearm were burned in the 90 C hot water bath.
An employee had climbed onto a machine platform and gotten down on his hands and knees to look for the cause of a defect in film that was running on a slitting machine. He slipped and his left hand went into the machine, where it was caught between a roller and a bar. He suffered broken tendons in the hand and wrist.
At approximately 0900, an employee was trying to move a pulp roll back into position on a pulp feed rack. The pulp roll slid off the rack onto the floor and caught the employee's right arm against the rack. The employee was hospitalized with a broken arm that required surgery.
An employee was taking lab waste to a special waste dumpster. The employee fell through grating adjacent to the special waste dumpster approximately 4 feet to the concrete floor and sustained broken bones in both feet.
Two employees were repairing the hydraulic engagement pins on a rented front-end wheel loader. The machine controls were activated to move the attachment pins and an employee's finger was caught between the pins and the bushings. Their right index finger was partially amputated.
An employee was cleaning the conveyor on a piece of equipment when they slipped and their right hand was pulled into the chain sprocket. The employee's fifth fingertip was amputated.
An employee was throwing blankets onto a blanket folding and stacking machine. A blanket got stuck in the machine and she attempted to remove it when the machine contacted her right little finger, resulting in a fingertip amputation.
More severe injuries in this industry (NAICS 325220)
A temporary employee cut back-wrapped material on an extrusion line. His left hand was caught in the material as he tried to clear it. As the material continued to rotate, the employee's left ring finger was severed, resulting in a partial amputation.
An employee was using a plastic pipe to clear a jam in the shredding equipment. The pipe got stuck in the shredder and went into a vertical position, crushing the employee's left ring finger between the pipe and the top of the shredder shroud. The employee sustained a fingertip amputation.
An employee was operating a stand-up forklift to move a pallet of product that was sitting on the floor in an aisle of the finishing warehouse next to metal racking. The forklift cab went under the middle shelf and his torso became caught between the metal shelf (at his back) and the forklift steering control stick (at his front). He was hospitalized with possible fractured ribs.
An employee was starting to collect edge trim when their right middle and ring fingers came into contact with a shear slitter blade. Half of the ring finger was nearly amputated, and half of the middle finger was amputated.
An employee was working to remove a product blockage from a piece of equipment. The employee was struck by a metal bar near the deck of the pin mixer equipment and sustained blunt force trauma to the torso.
An employee was moving a rack onto a lower conveyor in the south heat treat area when their finger got caught between the part tray and the rollers, resulting in a fingertip fracture and amputation.
An employee was climbing a ladder to get on top of the breakroom. The ladder slipped, causing him to fall to the ground. The employee sustained fractures to his upper back, left foot, and ankle.
Two employees were removing a circuit breaker. The injured employee was using wrenches in the removal process. One of the wrenches contacted an adjacent door, resulting in an arc flash. The employee suffered burns to their neck, face, and ear, as well as momentary vision loss due to the flash.
An employee bent over to pick up a rubber mat from the ground. When he grabbed the corner of the mat, a rattlesnake hidden under it bit his left middle finger near the first knuckle. He was hospitalized.