Builders First Source

An employee was measuring a block on a pedal-operated upcut saw equipped with a 10 or 12 inch circular blade. As he was taking a measurement, the blade contacted his left hand, resulting in amputations of three fingers.

Employees were stacking two different types of trusses in a yard. One employee was lifting one end of a truss with a forklift while another inserted a spreader block. The load shifted, and the second employee's left ring finger was pinched between the block and the trusses. The finger was amputated.

An employee had been installing door and inside trim at a location. The employee was cutting lumber with a chop saw and amputated his left middle and index fingers.

An employee was behind a truck, preparing to dump one of two pallets of lumber from the truck's dump body (which had been raised so the lumber could be unloaded). The other pallet slid off the truck and struck the employee's lower leg, breaking it.

An employee was stepping out of his delivery truck onto the street when he slipped on an ice buildup, injuring his hip.

An employee was preparing a tank car for loading while chipping away solidified product in the manway opening of the tank car. A pressure noise within the tank car startled the employee, causing him to stumble backward and fall approximately 10 feet over the guard railing at the chemical loading rack to the ground. The employee suffered fractured vertebrae, a fractured right wrist and ankle, and a dislocated jaw.

An employee was installing an electrical tray remover from a ladder. As he was descending, his missed a step and fell 6-7 feet to the floor. The employee suffered a head injury.

Two employees were installing spray foam insulation in the attic of a new residential construction. The injured employee fell 8 feet from an A-frame ladder to the floor. The employee suffered lacerations, abrasions, and a head injury.

An employee was on a raised platform attaching wires to electrical boxes. The employee fell approximately 8 feet to the floor below and struck an exit sign on the way down, resulting in an injury to his face.

An employee was in a forklift man basket fixing a garage door opener when they fell approximately 8 feet to the concrete ground below. The employee suffered head and back injuries as well as kidney bruising.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.