FLSmidth Inc.

An employee was machining a trunnion using a grinding rig when their left hand was caught between the grinding stone and the trunnion, resulting in fractures to the middle, ring, and little fingers, as well as severe damage to the skin and amputations of the middle and ring fingers to the distal knuckle.

An employee was using a hammer to hit a steel bearing and dislodge it from a shaft. A small piece of the bearing broke off and embedded in his stomach.

An employee was operating a hydraulic press when his left middle finger was crushed between the part he was pressing and the press table. The employee sustained an open fracture of the tuft of the distal phalanx, which led to a partial amputation of the left middle fingertip.

On May 6, 2020, at approximately 7:45 p.m., an employee stopped a lathe and pulled a nylon strap through the center of a 13-inch long, 8-inch diameter part. The nylon strap was attached to a jib crane, and the employee needed to jog the lathe to lock the chuck. The lathe did not jog and instead began running at operational speed. The employee's gloved right hand was caught between the nylon strap and rotating metal part, resulting in a broken thumb, severed nerves and tendons, and severe tissue damage to the hand.

A crew was pulling a 4-inch plastic gas pipe off a reel and straightening it for installation. The injured employee stepped up on the trailer to cut the last band holding the pipe in the coil on the reel. As he turned to step off the trailer, the end of the pipe rotated and sprung out of the cage surrounding the coil, striking the employee on the side of the head and knocking him off of the trailer into the roadway. The employee suffered head trauma that required hospitalization.

An employee and a co-worker were performing a pick inside a clear well. They rigged the skid pan that was full of broken concrete. When lifting, the load began to swing toward a wall. The employee tried to stop the skid pan from swinging and was struck by the pan, resulting in fractures to their left hip and wrist.

The employee had just completed refueling a lattice crane that was breaking up material and was winding the fuel hose back into the fuel truck when he was struck by the catwalk/stairs of the crane. The employee was hospitalized with a laceration to his backside, possible internal bleeding, and a broken hip.

An employee was fusing 10-inch black rubber utility pipes together using a pipe fusion machine and could not get the pipes to set correctly. The employee used a nylon strap attached to an excavator to lift one side of a pipe off a steel plate. As his hand was between two pipes, the pipes came back together, partially amputating two of his fingers.

An employee was lifting four bags of a lime blend weighing approximately 10,000 pounds using a crane. The load swung and pinned the employee against a structural I-beam, resulting in fractures to the hip and pelvis.

An employee was standing at the rear of a machine and the machine's mesh tray fell down onto the rear of the machine, crushing his left hand against the read lift. The employee sustained fractures and a laceration to their left hand and was hospitalized.

The injured employee was assisting with tightening down 3/4" hardware during assembly of a 6'x20' triple deck screen. Another employee was using a 1/2" cordless impact wrench to tighten down the hardware. The injured employee was using a 1-1/8" open-end wrench that slipped when the bolt was being tighten down by the impact wrench. The injured employee's right ring fingertip was caught between the open-end wrench and the side sheet of the triple deck screen. The tuft of the distal phalanx was amputated.

An employee was welding baffle plates onto a 55-gallon hydraulic tank. A flash occurred as they began to tack weld a part. The employee suffered burns to most of their face and second-degree burns on each arm, resulting in hospitalization.

An employee was cutting a piece of rubber with a utility knife. The knife slipped and partially amputated the employee's right index fingertip.

On July 22, 2024, an employee was using a pressure washer to fill a mop bucket with water. The washer's hose split and soapy water was injected into the employee's right palm and index finger. The puncture wound had to be surgically cleaned.

An employee tripped over a concrete curb stop in a parking lot. The employee fell to the ground, landing on their left hip and breaking it.

An employee was conducting routine maintenance on a mixer. New lid pins had been installed, and the employee was rotating by hand to ensure they had been installed correctly. The employee's left middle finger was caught between the lid and top of a pin. The momentum from the mixer continued, causing a crushing injury to the finger. The employee underwent a medical amputation from the top knuckle to the tip of the finger.

An employee was climbing down a ladder when it slipped. The employee fell, suffering a broken scapula and broken ribs. The employee was hospitalized.

An employee was climbing down a 15-foot multipurpose ladder. The employee fell about 8 feet, landing on the concrete floor and the ladder itself. The employee suffered several injuries, all on the right side: broken ribs, a broken sternum, a broken temporal bone, broken shoulder, multiple fractures to the cheekbone, and a brain bleed.

An employee was rolling up the landing gear on his trailer when the handle began to unwind and struck his face, fracturing his jaw. The employee was hospitalized and required surgery.