Tyson Foods

An employee was trimming beef when the knife came out of his hands and punctured his abdomen as he went to grab it. The employee sustained an open abdominal wound with no internal injuries.

An employee was rigging two hooks together that were attached to a pallet and pulled by a forklift. The employee's finger slid under the secondary hook attached to the forklift and sustained a left index fingertip amputation.

An employee was helping mechanics remove a piece of iron from an airlock. The employee was approximately 3 feet up on a ladder when he dropped a wrench, which struck the handle of the steam line valve. The valve opened and steam sprayed onto the employee, causing burns to both inner thighs and his lower abdomen.

An employee was bending over, setting up a pallet on the floor. As she stood up, she lost balance, slipped, and fell to the floor, sustaining a fractured right ankle.

An employee was operating a forklift and scanning a barcode. The employee went to exit the lift when his left foot struck the edge of the lift, causing him to fall to the floor. The employee was hospitalized for a hip fracture.

An employee was installing a 15-amp breaker in an electrical panel when a 12-gauge ground wire touched the positive busbar of the panel, resulting in an arc flash. The employee sustained a second-degree burn to their left hand.

An employee was repairing an HVAC system in the drop tile ceiling of a conference room when they were shocked, causing them to fall from the ladder. The employee sustained burns to their right middle and ring fingers.

An employee was replacing a contactor inside an electrical panel attached directly to a press. The press itself was receiving power from another main panel. After replacing the contactor, the employee flipped the switch and an arc flash occurred, burning the employee's elbow, bicep, and neck.

An employee was attempting to switch a medium-voltage primary cable and install a 200-amp fuse barrel. The employee contacted the bottom of the switch gear cradle for the fuse barrel, causing an arc blast. The electricity entered the employee s left hand and exited his big toes, resulting in electric shock and burns to the left hand, arm, shoulder, and both feet. The employee was hospitalized.

On December 6, 2023, an employee of Duke Energy was working on a single-phase 120-/240-volt parallel service re-tap when a secondary flash occurred in an underground service. The employee suffered a second-degree burn to the face and was hospitalized.

An employee was scraping dried glue from the top lid of a hot glue pot. His left hand slipped and came into contact with the hot glue. He then suffered burns to his hands and fingers as he tried to remove the glue. He was hospitalized.

An employee was in a scissor lift approximately 20 feet above the ground to place a plastic tarp on a catwalk in order to catch condensation. They positioned the lift opposite the work area and stepped out of the scissor lift onto an I-beam. The employee fell from the I-beam to the ground. The employee was hospitalized with a skull fracture on the right side of their head and injuries to the chest and both eyes.

A maintenance employee was called to look at a pallet conveyor machine where a chain had fallen off a sprocket wheel. When the employee grabbed the loose chain, a light sensor caused the machine to restart. This created a pinch point between the chain and sprocket that caught the employee's left little finger. The finger was surgically amputated at the second knuckle.

The injured employee was standing by one of the stationary computers along the wall. There was a half-pallet located approximately 3 feet behind the employee that consisted of 12-pound boxes stacked six boxes high. A forklift was transporting a pallet that came in contact with the stationary pallet behind the injured employee, causing four boxes to fall and contact their legs. The injured employee was hospitalized with leg injuries.

An employee was using a box strapping machine to place straps on boxes when his right middle finger was caught in the machine, resulting in an open fracture to the distal phalanx.

An employee was stacking concrete blocks for a concrete bunker. As a block was swinging into place, the employee's left leg was pinched between two blocks, resulting in injuries to his left heel and lower leg.

An employee was climbing a ladder to inspect a vent in a restaurant dining area. The ladder slid out on the floor and the employee fell approximately 12 feet onto the ladder and the floor. He was hospitalized with a dislocated shoulder and a back injury.

An employee was rappelling down a tree. When he was most of the way down, he fell on the ground and suffered a broken pelvis.

An employee was filtering a fryer with a fryer filter machine. After going around the corner and then returning to the fryers, the employee stepped into the filter machine. The hot oil burned the employee's right ankle, and the employee was hospitalized.

An employee was cleaning out corn from a grain bin. The sweep auger in the bin was activated and caught his trouser leg. His leg was pulled into the auger, which injured his calf and caused leg fractures and lacerations.