Commercial Metals Company

A rolling mill was shut down due to a cobble between two mill stands. The injured employee was cleaning the cobble from the delivery side of stand A, while another employee went to the control panel to move stand B and stand A moved instead. The injured employee's right thumb got caught between the delivery guide of stand A and the looper trough. The tip of his thumb required surgical amputation to the bone to allow for stitches.

A truck driver was walking on top of a load of logs to remove tarps. He approached the edge to prepare for dismounting. He stepped on a sideboard that shifted, causing him to fall to the ground. He sustained a cut to the top of his head that required five stitches, fractures to his right forearm, and a dislocated right elbow.

An employee entered the baghouse to take dust samples from a compartment. When he entered the building there was baghouse dust approximately 12 inches deep on the floor. The employee walked through the dust about 5 feet when he noticed the layer of dust beneath the top was hot and felt his feet burning. Heated dust had entered the top of his boot and worked downward until resting underneath the arch of his right foot causing burns to the bottom of his foot.

An employee was using a crane to move a 6-by-60-foot bundle of rebar from a stock rack to production lines. The employee placed the crane remote on an adjacent bundle and was placing the wire sling under the suspended bundle when the remote control slid off the adjacent bundle and fell under the suspended bundle. The employee reached under the suspended bundle when the bundle tie wire suddenly broke. The bundle fell onto the employee's right hand, resulting in a crushed and fractured hand.

An employee was working between railcars on an active railroad track to connect the airbrake. Another employee moved the railcars, striking and running over the employee resulting in amputation of both legs.

An employee was walking down the hallway when they tripped and fell to the floor, fracturing their right wrist.

An employee was walking down the hall to retrieve a vacuum when they stumbled and fell to the floor. The employee suffered wrist bruises and a kneecap fracture that required surgery.

An employee was carrying furniture backward during a delivery when he tripped and broke his right ankle.

An employee was installing a compressor piston. He tripped and fell backward while the piston was in his lap. As he landed, the little finger of his left hand became caught between the piston and compressor piping resulting in a partial amputation of the fingertip. The employee required stitches and the fingertip was reattached.

An employee was doing an oil change. He was walking to get his oil jug when he tripped on an open lift pad, and fell to the ground landing on his right side. The employee sustained a broken right femur and was hospitalized.

An employee fell while entering the building. The employee was hospitalized with a fractured ankle and required surgery.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was working to close a furnace door. The hydraulic mechanism that opens and closes the furnace door was non-operational and had been disconnected to allow the furnace door to be opened manually. As the employee was releasing the pins that held the door open, the door and the hydraulic cylinder fell, pinching their left hand between the hydraulic cylinder's base plate and the furnace. The employee suffered amputation of the little fingertip.

A rolling mill was shut down due to a cobble between two mill stands. The injured employee was cleaning the cobble from the delivery side of stand A, while another employee went to the control panel to move stand B and stand A moved instead. The injured employee's right thumb got caught between the delivery guide of stand A and the looper trough. The tip of his thumb required surgical amputation to the bone to allow for stitches.

An employee was helping another employee load stock material onto a press brake when the stock slipped. The injured employee's right index finger was caught between the press brake die and the stock, resulting in amputation at the first knuckle.

An employee tripped over a stool and fell on the floor, resulting in a left displaced mid-cervical femoral neck fracture.

An employee was installing fence posts when they stepped into a recently dug hole that was not visible due to rainfall. The employee's leg was fractured.

An employee assisted in cleaning material from a conveyor pit. After the pit was cleaned, the employee proceeded to replace metal safety plates to ensure other employees did not fall into the pit. While replacing one of the last plates, the employee mis-stepped and fell approximately 5 feet into the pit. The employee was hospitalized with back/side bruising, elbow bruising, bone bruises, and/or fractured ribs.

An employee was inspecting a breaker box and turning on/off a circuit breaker when he was electrocuted.

An employee was walking on the sidewalk. When they stepped off the curb, they fell to the ground, resulting in fractures to their tibia, fibula, and a metatarsal.