JBS SWIFT

An employee entered the drive alley to close the gate. The cattle turned back and struck the gate catching the employee between the gate and the wall. The employee sustained multiple rib fractures and a traumatic pneumothorax.

An employee was loading grease into a tanker. The employee was splashed with the grease and suffered severe burns to the right arm and hand. The employee was hospitalized.

An employee was unjamming a beef hide from a flesher machine when the flesher wheel closed on the employee's arm, fracturing the upper arm and wrist. The machine was guarded at the time of the incident, but was not locked out.

An employee was performing walking cuts on the kill floor. As he attempted to make a cut, he missed and contacted the knife of a coworker, lacerating his right forearm.

An employee was investigating the cause of a mechanical malfunction on a centrifuge used to process waste water. While the employee was pulling on a belt and pulley mechanism, the weight of the belt crushed the employee's left index finger, requiring surgery and overnight hospitalization.

An employee was using a crane. The hook slipped and a fitting fell onto a finger on the employee's left hand causing a fracture and laceration.

An employee was transporting an 800-pound die on a cart from the tool room. The employee was pulling the cart when it struck a metal plate on the floor. This caused the cart to tip forward and the die to slide off the cart. The die struck the employee's left foot and their second toe was amputated.

An employee was using a forklift to load pallets of product on a trailer. He exited the forklift to adjust a pallet by hand. The pallet fell on him, resulting in an injury to the left leg.

An employee was lifting a 500-pound steel counterweight off a pallet using a magnetic hold jib crane. The counterweight detached from the crane and the employee sustained a left foot/toe fracture that required surgery.

An employee was using a pipe wrench to turn a 42-foot-long steel pipe on jack stands to weld the bottom portion. The pipe fell off the stands, striking the injured employee on his left shin. The employee sustained a left leg fracture at the shin area as well as a tibia fracture that required surgery.

An employee was scraping dried glue from the top lid of a hot glue pot. His left hand slipped and came into contact with the hot glue. He then suffered burns to his hands and fingers as he tried to remove the glue. He was hospitalized.

An employee was in a scissor lift approximately 20 feet above the ground to place a plastic tarp on a catwalk in order to catch condensation. They positioned the lift opposite the work area and stepped out of the scissor lift onto an I-beam. The employee fell from the I-beam to the ground. The employee was hospitalized with a skull fracture on the right side of their head and injuries to the chest and both eyes.

A maintenance employee was called to look at a pallet conveyor machine where a chain had fallen off a sprocket wheel. When the employee grabbed the loose chain, a light sensor caused the machine to restart. This created a pinch point between the chain and sprocket that caught the employee's left little finger. The finger was surgically amputated at the second knuckle.

The injured employee was standing by one of the stationary computers along the wall. There was a half-pallet located approximately 3 feet behind the employee that consisted of 12-pound boxes stacked six boxes high. A forklift was transporting a pallet that came in contact with the stationary pallet behind the injured employee, causing four boxes to fall and contact their legs. The injured employee was hospitalized with leg injuries.

An employee was using a box strapping machine to place straps on boxes when his right middle finger was caught in the machine, resulting in an open fracture to the distal phalanx.

An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.

An employee was cutting cabinet trim using a table saw when four fingers on his left hand were severed, resulting in hospitalization and amputation.

An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.

A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.