SERVICE ELECTRIC COMPANY

Employee 1 had just finished disassembling a metal girder structure on the ground and had removed the bolts from its metal cross brace. Employee 1 then moved to the left side of the structure. Employee 2 was using a skid steer to pick up the metal cross brace. Once the cross brace was on the forks of the skid steer, employee 1's right leg was caught between the cross brace and the metal girder structure. Employee 1 was hospitalized with a fractured right leg, which required surgery to repair.

Employees were replacing an overhead utility line switch with a new set of switchgear. The injured employee was tightening a bolt to complete the last step of the work when an arc flash occurred and the employee was shocked.

Employees were in a mobile crane when it collapsed. They fell approximately100 feet to the ground and two employees were hospitalized. One employee sustained a hip injury and the other employee sustained a lung injury.

Employees were performing water-based excavation using a hydrovac truck. The stream of pressurized water lacerated an employee's left foot.

The employee was rigging a towing strap to a front-end loader to tow a truck out of the mud and onto matting. The front-end loader moved while the employee's thumb was between the vertical drop pin and the tow bar of the front-end loader, resulting in a partial thumb tip amputation.

An employee was installing a 15-amp breaker in an electrical panel when a 12-gauge ground wire touched the positive busbar of the panel, resulting in an arc flash. The employee sustained a second-degree burn to their left hand.

An employee was repairing an HVAC system in the drop tile ceiling of a conference room when they were shocked, causing them to fall from the ladder. The employee sustained burns to their right middle and ring fingers.

An employee was replacing a contactor inside an electrical panel attached directly to a press. The press itself was receiving power from another main panel. After replacing the contactor, the employee flipped the switch and an arc flash occurred, burning the employee's elbow, bicep, and neck.

An employee was attempting to switch a medium-voltage primary cable and install a 200-amp fuse barrel. The employee contacted the bottom of the switch gear cradle for the fuse barrel, causing an arc blast. The electricity entered the employee s left hand and exited his big toes, resulting in electric shock and burns to the left hand, arm, shoulder, and both feet. The employee was hospitalized.

On December 6, 2023, an employee of Duke Energy was working on a single-phase 120-/240-volt parallel service re-tap when a secondary flash occurred in an underground service. The employee suffered a second-degree burn to the face and was hospitalized.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.

Employees were securing the fuel line of an outboard motor in preparation for removing the motor from a small vessel located in the equipment yard. A gasoline-related fire occurred and one employee sustained burns to both hands and forearms.

A marine diver/construction worker was working underwater, using a hydraulic dredge to clear sediment away from the base of a dam. The dredge's suction nozzle began migrating toward him, and then pulled in his right hand and forearm. He sustained compartment syndrome in the hand and forearm.

An employee was standing on a sheet of -inch by 4-foot by 8-foot plywood on top of a rebar mat, supervising his crew. As he was moving to alert the crew to an incoming overhead load, he stepped off the plywood and his left foot slipped through the rebar mat and landed on the rebar mat below. His left ankle was broken and dislocated.

An employee was helping a coworker transport a tall palm tree with a mini skid steer. The employee was severely shocked by a high-voltage electrical wire above the ground.

An employee was retrieving a Christmas tree from a shelf using a ladder. He missed a step and fell to the concrete floor. He sustained injury to his head and wrist.

An employee was inspecting a generator whose radiator was leaking. He slipped, and a fan blade in the generator amputated his thumb and index finger.

An employee was operating an agricultural tractor during sugarcane harvesting. The employee sustained a lumbar sprain due to vibration or motion from the tractor.

An employee was moving a 3-ton condensing unit, strapped down on a dolly, out of a garage. The strap broke, causing the employee to fall backward onto the brick pavered driveway. The employee suffered injury to a spinal ligament in the neck.