The Boeing Company

Two employees fell from an access bridge while entering an aircraft to perform maintenance. They landed on the ground about 20 feet below, where one of them lost consciousness. One employee sustained a fractured knee and another employee sustained a back strain/sprain. Both employees were hospitalized.

An employee was cleaning up a fuel barn. They were winding up a power cord when they tripped on the cord and fell to the concrete floor, resulting in a fractured left wrist that required hospitalization and surgery.

In the flight line area, an employee was on a work stand platform conducting repairs to an aircraft. While transitioning to another location, he stepped over another employee and lost his balance. The employee reached for the railing to catch themselves, fell, and tore his right bicep. The employee was hospitalized for surgery.

Employees were working on a machine overhaul. They were using a hydraulic jack to move the machine laterally into position. The machine shifted and pinched an employee's hand against the concrete floor. A fingertip was amputated.

An employee was walking in the breezeway outside the orbital processing facility when a vent hood on two wooden supports tipped over onto them. The employee was trapped underneath the vent hood, resulting in hospitalization for fractures to their rib and sternum.

An employee was climbing a step ladder while carrying a 3-foot piece of conduit. As he went to reposition his feet on the ladder by pivoting, he slipped and fell from the third rung of a 6-foot ladder. The employee sustained fractures to the left femur, right elbow, and right ring finger.

An employee was descending a 4-step maintenance stand when she missed the bottom step and fell to the hangar floor. The employee suffered a left hip fracture.

An employee stopped a belt and was going to check it for missing packages. She fell backward 3-4 feet from an elevated platform and sustained a broken right arm.

An employee had just finished a routine concrete pour and was ascending the ladder to clean the concrete mixer truck. The employee lost their grip and fell approximately 2-3 feet, contacting the truck's bumper. The employee suffered rib fractures and a punctured lung.

An employee was performing duties as an expeditor. After opening the dock door, the employee scanned the barcode on the door of the truck and placed one foot on the truck and one foot on the dock. The truck drove out of the stall, causing the employee to fall 4 feet off the dock onto the concrete. The employee sustained fractures to the right side of the pelvis, elbow, and a left ring fingertip as well as injuries to the right wrist and bruising to the back and stomach.

A pressurized aircraft nose landing gear strut assembly was being disassembled. The gland nut dislodged under pressure and made contact with an employee's left hand, breaking it.

A metal tooling base was being moved by a forklift when the load shifted. An employee who was assisting went to stabilize the load and prevent it from sliding off the forks. The C-channel of the base crushed the employee's left hand against the concrete ground, resulting in the amputation of their third and fourth fingers.

An employee was working on a tool platform (47.5" tall) and was transitioning around to the other side when they lost balance and fell to the concrete floor. The employee was hospitalized with fractures to seven ribs and their elbow.

An employee was adjusting the task lighting on a band saw when their right little finger made contact with the blade, resulting in amputation.

On August 19, 2025, at 6:30 a.m., an employee sat in the rear bench seat of a golf cart ahead of being driven to a parking lot. When the golf cart began to move, he fell off the cart and onto the ground, resulting in a fractured right hip.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was preparing hot melted butter on a flat-top grill and placing it in small containers once it was melted. As she turned to set the container down, it slipped out of her hand and landed on the grill. Butter splashed up and hit her in the face. The employee suffered second-degree burns to her right eye and the right side of her head and face, as well as first-degree burns to her right forearm.

An employee pulled into the customer's driveway, parked, and exited the vehicle. He opened the sliding side door on the vehicle to retrieve a package. The customer began backing their vehicle out of their garage and it struck the employee in the back of his left leg. He was pinned him between the two vehicles, causing contusions and lacerations.

An employee reached into a hamper, picked up a package, and was hospitalized with a back injury that caused pain in his lower extremities.

On July 10, 2025, an employee tripped over a yellow pillar and fell to the floor. The employee was hospitalized with a fractured left femur.