Struck against moving part of machinery or equipment · Amputations
At a glance
Federal OSHA recorded a severe workplace injury
at LOCKHEED MARTIN, Ft Carson CO, FT CARSON, COLORADO 80913
on — Amputations, affecting the finger(s), fingernail(s), n.e.c..
Final narrative
An employee was using a clutch spreader tool during a training activity. When he applied pressure to the tool to release belt pressure, his left index finger came in contact with a spring sheave roller. The finger was amputated just below the nail.
An employee was troubleshooting a dust collector when they sustained partial amputations to three of their right fingertips from the spinning rotor of the motor.
On June 27, 2023, at 2:30 p.m., a pilot was returning after a test flight of an F-35 aircraft. After aircraft recovery, the pilot exited the aircraft via the integrally mounted aircraft access ladder. During his descent, he tripped on the third ladder step and fell approximately 6 feet, resulting in a dislocated left shoulder, a compound dislocation of the left elbow, and stable fractures of the left 7th and 8th ribs.
A 370-pound piece of aluminum was being lifted with a jib crane and a calibrated suction lifting fixture. The aluminum fell, landing on an employee's left foot about 3 feet below. He was hospitalized; his big toe had been broken, and the other four toes were medically amputated.
An employee was in a final assembly building, seated on a workbench chair with wheel casters, working on equipment wiring. The chair slid out from under the employee, who fell about 2 1/2 feet to the concrete floor and suffered a broken hip and right femur.
An employee was operating a strip saw. As the employee shut off the saw, their right index and middle fingertips were amputated by the blade before it came to a complete stop.
An employee was using a table saw to cut a piece of wood for wall framing. The wood jumped, causing the employee's hand to move toward the saw, amputating their left index finger and causing a laceration on their hand.
An employee was operating a trim saw. While trying to free a jammed board she had just cut, she came into contact with the running saw blade, which amputated her right thumb.
Two employees were removing a service lift platform from the back of a radar system. While handling the service lift platform, employee 2 was standing on the back of the radar and lost their footing, causing the service lift platform to shift and fall. The injured employee then fell from the top of the platform electronic subsystem (PES) to the floor, approximately 56 inches. The injured employee fractured his left elbow and left hip.
On June 27, 2025, an employee was walking out of the hangar when he tripped and fell on the concrete ramp. He sustained lacerations to his right elbow and right hand, and was hospitalized with a fractured right hip.
An employee was performing maintenance activities on a ladder when they fell approximately 46 inches to the ground, resulting in a fracture to the left pelvis/sacrum.
An employee was loading a 150-pound block of aluminum into a CNC machine when their right hand was struck by the block. The employee sustained a fracture and severed tendon to the index finger, as well as a laceration to the middle finger that required stitches.
An employee picked up material out of a cardboard box that was on the floor. As he was carrying the material, he stepped backward and tripped over the cardboard box, causing him to fall and suffer a compound fracture of his leg.
An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.
An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.
A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.
An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.