National Beef Packing Company, LLC

An employee was operating a rib saw and sustained a laceration to their left palm, which required hospitalization.

An employee was removing a section of a conveyor that weighed 40-50 lbs. when it slipped and caused a laceration to their little toe that resulted in amputation.

An employee was cleaning the blender in the ground beef department and amputated two fingertips.

An employee was shackling livestock when his finger contacted the chain and tension bar, resulting in a fingertip amputation.

An employee was working on a metal cover on a second-level carousel. The employee fell about 14 feet to the floor below, suffering a contusion to the left side of the body, a contusion with abrasion/swelling to the back of the head, a contusion/abrasion to the front of the left hand, a contusion (and pain) to the left shoulder, and a contusion/swelling to the left hand/wrist.

An employee was operating a metal roller machine to roll a small piece of metal. The employee's right index finger became caught between the metal and the machine, and the fingertip was amputated.

An employee was mixing sauce using a sauce barrel mixer when his left little finger was amputated.

An employee was working on a production line. The employee went to retrieve parts that came out of the parts holder, and their left hand became caught between a chain and a sprocket. Three fingers on the hand were amputated.

An employee was hooking up bundled tie-downs with a chain. While he was holding a hook, the other hook was unlocked. This caused the employee's hook to slide down and pinch his right index finger between the chain and the shackle. He suffered an amputation to the fingertip (without bone loss), as well as an open fracture.

An employee was operating a pad printer. The employee's finger was caught in the printer and they suffered a fingertip amputation. The part of the printer that caught the employee's finger was unguarded at the time.

An employee was scraping dried glue from the top lid of a hot glue pot. His left hand slipped and came into contact with the hot glue. He then suffered burns to his hands and fingers as he tried to remove the glue. He was hospitalized.

An employee was in a scissor lift approximately 20 feet above the ground to place a plastic tarp on a catwalk in order to catch condensation. They positioned the lift opposite the work area and stepped out of the scissor lift onto an I-beam. The employee fell from the I-beam to the ground. The employee was hospitalized with a skull fracture on the right side of their head and injuries to the chest and both eyes.

A maintenance employee was called to look at a pallet conveyor machine where a chain had fallen off a sprocket wheel. When the employee grabbed the loose chain, a light sensor caused the machine to restart. This created a pinch point between the chain and sprocket that caught the employee's left little finger. The finger was surgically amputated at the second knuckle.

The injured employee was standing by one of the stationary computers along the wall. There was a half-pallet located approximately 3 feet behind the employee that consisted of 12-pound boxes stacked six boxes high. A forklift was transporting a pallet that came in contact with the stationary pallet behind the injured employee, causing four boxes to fall and contact their legs. The injured employee was hospitalized with leg injuries.

An employee was using a box strapping machine to place straps on boxes when his right middle finger was caught in the machine, resulting in an open fracture to the distal phalanx.

An employee was working to remove a product blockage from a piece of equipment. The employee was struck by a metal bar near the deck of the pin mixer equipment and sustained blunt force trauma to the torso.

An employee was moving a rack onto a lower conveyor in the south heat treat area when their finger got caught between the part tray and the rollers, resulting in a fingertip fracture and amputation.

An employee was climbing a ladder to get on top of the breakroom. The ladder slipped, causing him to fall to the ground. The employee sustained fractures to his upper back, left foot, and ankle.

Two employees were removing a circuit breaker. The injured employee was using wrenches in the removal process. One of the wrenches contacted an adjacent door, resulting in an arc flash. The employee suffered burns to their neck, face, and ear, as well as momentary vision loss due to the flash.

An employee bent over to pick up a rubber mat from the ground. When he grabbed the corner of the mat, a rattlesnake hidden under it bit his left middle finger near the first knuckle. He was hospitalized.