Struck by suspended or swinging objects n.e.c. · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at Acme Erectors, Inc., Continental Tire America, MOUNT VERNON, ILLINOIS 62864
on — Fractures , affecting the Trunk and other upper extremities.
Final narrative
Two employees were unloading a steel column from a flatbed tractor trailer. The two-point rigging configuration slipped on the load as it was being hoisted off the trailer. The two rigging points slid on the column and came together, causing one end of the column to strike the injured employee's arm. The employee was knocked down, and he landed on his side on the flatbed trailer. The end of the column then landed on his hip. The employee was hospitalized with a fractured arm and pelvis and required surgery.
Hospitalized Trunk and other upper extremities Beams and rails metal
An employee was driving a scissor lift (in the down position) up a wooden site-built ramp. He had to turn the lift to the right as he started climbing the ramp. The left front wheel of the lift dropped off the edge of the ramp, causing the lift to tilt slightly to the left. The employee jumped out and landed on his right elbow on the concrete floor. His humerus was broken just above the elbow.
An employee was walking into the motor control center (MCC) room when his right ring finger was caught in the hinge of a doorway. He sustained an open phalanx fracture, which resulted in a partial amputation above the first knuckle.
An employee was stacking concrete blocks for a concrete bunker. As a block was swinging into place, the employee's left leg was pinched between two blocks, resulting in injuries to his left heel and lower leg.
An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.
An employee was placing a board on top of a bundle of steel tubing. A crane was moving a bundle of steel that struck the employee and caught them against another bundle of steel tubing. The employee sustained a crushing injury and hematoma to the right upper leg.
Employees were using a crane to lower large tree stems and branches while removing limbs and branches from the load. This caused the load to shift and strike an employee in the back, resulting in a hematoma on the lower left part of their back and a fractured ankle.
More severe injuries in this industry (NAICS 238120)
An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.
An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.
An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.
An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.
An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.
An employee was changing a die in a press when the die slipped and crushed the employee's left index finger. The employee sustained an open facture of the tuft of the left distal phalanx and a partial amputation.
An employee was driving a boom lift (in the lowered position) in an exterior dock area. The lift s left wheels rolled onto base plates that covered a 3-foot-deep sump pit. The base plates failed, and one side of the lift dropped. The employee's left leg was caught under the lift basket, and he suffered a fracture to the lower leg including the ankle.