MILWAUKEE, WISCONSIN—
MAYNARD STEEL CASTING COMPANY
Ignition of clothing from controlled heat source · Third or fourth degree heat (thermal) burns
At a glance
Federal OSHA recorded a severe workplace injury at MAYNARD STEEL CASTING COMPANY, 2856 South 27th Street, MILWAUKEE, WISCONSIN 53215 on — Third or fourth degree heat (thermal) burns, affecting the leg(s), unspecified.
Final narrative
An employee was supervising coworkers who were pouring castings when heat from the castings ignited the employee's clothes, causing second and third degree burns to both legs. Proper PPE was not worn at the time of the incident.
Similar incidents · Same event type
FAIRLESS HILLS, PENNSYLVANIA—
Falls Manufacturing Company/a U-Haul Co.
An employee was welding metal parts. The employee turned to the left and their work uniform came in contact with the location on the part that had just been welded. The employee's uniform ignited, causing burns to their shoulder and back.
CORDELE, GEORGIA—
Flint Ag & Turf
An employee was using a small propane heater when they sustained third-degree burns to the left buttock and second-degree burns to the back and neck.
WAYNESBORO, PENNSYLVANIA—
Novae, LLC.
An employee was welding steel dump ramp slides. He leaned over and a previous weld caught his hoodie on fire. The employee sustained burns on his left side from the armpit to the waistline.
LEWISBURG, PENNSYLVANIA—
Pik Rite Inc.
An employee was using a fiber wheel to cut a 55-gallon drum to make a trash can. As they were cutting, sparks flew into the barrel and fire came out of a hole on the barrel, catching the employee's shirt on fire. The employee sustained burns to their abdomen and chest, requiring hospitalization.
KILLDEER, NORTH DAKOTA—
DC Power Tong, LLC
An employee was removing tubing caps and cleaning tubing ends with solvent. Their flame-resistant pants became soaked with the cleaning solvent and were ignited by a propane torch used for removing tubing caps. The employee was hospitalized with burns to their legs.
More severe injuries in this industry (NAICS 331513)
BATH, PENNSYLVANIA—
Effort Foundry, Inc.
An employee was unloading metal from two drums on a pallet. The employee removed the lid from the second drum and the drum fell over onto his ankle. The employee sustained a fractured ankle.
BATH, PENNSYLVANIA—
Effort Foundry, Inc.
An employee was working with team members on the pouring line, casting a sand mold. Molten metal entered the employee's personal protection suit and severely burned his left leg, calf, and ankle.
PEWAUKEE, WISCONSIN—
Northern Stainless Corporation
An employee was jointing a board with a jointer. The board jumped when it came into contact with the jointer's cutter head, and the jolt caused the employee's left hand to slide between the board and the guard and come into contact with the cutter head. He suffered lacerations/partial amputations to the middle, ring, and index fingers.
WAUKESHA, WISCONSIN—
MetalTek International, Inc.
An employee was turning off a gas valve when he bumped into a die brush and struck the spinning die. The die pin struck him on the back, resulting in contusions, abrasions, and a severe laceration to his back that required hospitalization and surgery.
PILOT POINT, TEXAS—
Staley Steel LLC
At 11:45 a.m. on June 13, 2025, an employee of Staley Steel, LLC, was performing preventive maintenance on an overhead crane. While he was holding a grease gun hose and nozzle, he contacted electrical components inside an electrical box. He suffered a first-degree electrical burn on the palm of the left hand, as well as pain up his left arm to the shoulder, and was hospitalized.
More severe injuries in WISCONSIN
MADISON, WISCONSIN—
RG Professional Carpenter, Inc.
The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.
FRANKLIN, WISCONSIN—
General Thermodynamics, Inc.
An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.
SAINT CLOUD, WISCONSIN—
Sargento Foods Inc
A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.
HIXTON, WISCONSIN—
Asher Enterprises, Inc.
An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.
VERONA, WISCONSIN—
Consolidated Electrical Distributors Inc.
An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.