Caught in running equipment or machinery during maintenance, cleaning · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at SPIRIT AEROSYSTEMS, INC., 3801 S. OLIVER ST., WICHITA, KANSAS 67210
on — Fractures, affecting the hand(s), unspecified.
Final narrative
An employee was operating an auto fastening machine when the machine failed to complete a tool change. The employee was attempting to troubleshoot the problem when the sensor cleared and the machine cycled, catching, fracturing, and puncturing the employee's right hand. The machine was not in stop mode at the time of the incident.
HospitalizedHand(s), unspecifiedSpecial process machinery, n.e.c.
A metal tooling base was being moved by a forklift when the load shifted. An employee who was assisting went to stabilize the load and prevent it from sliding off the forks. The C-channel of the base crushed the employee's left hand against the concrete ground, resulting in the amputation of their third and fourth fingers.
An employee was working on a tool platform (47.5" tall) and was transitioning around to the other side when they lost balance and fell to the concrete floor. The employee was hospitalized with fractures to seven ribs and their elbow.
An employee was working inside the access panel of a sliding door when the door began to shut. The employee's left middle finger was pulled into the chain and sprocket, resulting in amputation to the middle knuckle.
An employee was installing a rail on a machine. The roller pack was locked up, causing the chuck to not move. While manually removing the chuck, the rails were damaged. As a result, both the roller pack and the rail needed to be replaced. A fixed magnet from above the rail pulled the rail up and rolled it, pinching the employee's thumb between the rail and the magnet when he tried to install the new rail back to the position. The right thumb tip was amputated.
Two employees were repairing the hydraulic engagement pins on a rented front-end wheel loader. The machine controls were activated to move the attachment pins and an employee's finger was caught between the pins and the bushings. Their right index finger was partially amputated.
An employee was cleaning the conveyor on a piece of equipment when they slipped and their right hand was pulled into the chain sprocket. The employee's fifth fingertip was amputated.
An employee was throwing blankets onto a blanket folding and stacking machine. A blanket got stuck in the machine and she attempted to remove it when the machine contacted her right little finger, resulting in a fingertip amputation.
More severe injuries in this industry (NAICS 336413)
An employee was walking from one building to another when he slipped on wet concrete and fell. The employee was hospitalized with a fracture and dislocation of the right patella.
An employee was working inside the access panel of a sliding door when the door began to shut. The employee's left middle finger was pulled into the chain and sprocket, resulting in amputation to the middle knuckle.
An employee was installing a rail on a machine. The roller pack was locked up, causing the chuck to not move. While manually removing the chuck, the rails were damaged. As a result, both the roller pack and the rail needed to be replaced. A fixed magnet from above the rail pulled the rail up and rolled it, pinching the employee's thumb between the rail and the magnet when he tried to install the new rail back to the position. The right thumb tip was amputated.
An employee was working to remove a product blockage from a piece of equipment. The employee was struck by a metal bar near the deck of the pin mixer equipment and sustained blunt force trauma to the torso.
An employee was moving a rack onto a lower conveyor in the south heat treat area when their finger got caught between the part tray and the rollers, resulting in a fingertip fracture and amputation.
An employee was climbing a ladder to get on top of the breakroom. The ladder slipped, causing him to fall to the ground. The employee sustained fractures to his upper back, left foot, and ankle.
Two employees were removing a circuit breaker. The injured employee was using wrenches in the removal process. One of the wrenches contacted an adjacent door, resulting in an arc flash. The employee suffered burns to their neck, face, and ear, as well as momentary vision loss due to the flash.
An employee bent over to pick up a rubber mat from the ground. When he grabbed the corner of the mat, a rattlesnake hidden under it bit his left middle finger near the first knuckle. He was hospitalized.