Spirit Aerosystems Inc

A metal tooling base was being moved by a forklift when the load shifted. An employee who was assisting went to stabilize the load and prevent it from sliding off the forks. The C-channel of the base crushed the employee's left hand against the concrete ground, resulting in the amputation of their third and fourth fingers.

An employee was working on a tool platform (47.5" tall) and was transitioning around to the other side when they lost balance and fell to the concrete floor. The employee was hospitalized with fractures to seven ribs and their elbow.

An employee was working inside the access panel of a sliding door when the door began to shut. The employee's left middle finger was pulled into the chain and sprocket, resulting in amputation to the middle knuckle.

An employee was installing a rail on a machine. The roller pack was locked up, causing the chuck to not move. While manually removing the chuck, the rails were damaged. As a result, both the roller pack and the rail needed to be replaced. A fixed magnet from above the rail pulled the rail up and rolled it, pinching the employee's thumb between the rail and the magnet when he tried to install the new rail back to the position. The right thumb tip was amputated.

An employee was walking in the shop area, tripped on a work platform, and fell to the floor. The employee was hospitalized for a fractured femur.

An employee was climbing a step ladder while carrying a 3-foot piece of conduit. As he went to reposition his feet on the ladder by pivoting, he slipped and fell from the third rung of a 6-foot ladder. The employee sustained fractures to the left femur, right elbow, and right ring finger.

An employee was descending a 4-step maintenance stand when she missed the bottom step and fell to the hangar floor. The employee suffered a left hip fracture.

An employee stopped a belt and was going to check it for missing packages. She fell backward 3-4 feet from an elevated platform and sustained a broken right arm.

An employee had just finished a routine concrete pour and was ascending the ladder to clean the concrete mixer truck. The employee lost their grip and fell approximately 2-3 feet, contacting the truck's bumper. The employee suffered rib fractures and a punctured lung.

An employee was performing duties as an expeditor. After opening the dock door, the employee scanned the barcode on the door of the truck and placed one foot on the truck and one foot on the dock. The truck drove out of the stall, causing the employee to fall 4 feet off the dock onto the concrete. The employee sustained fractures to the right side of the pelvis, elbow, and a left ring fingertip as well as injuries to the right wrist and bruising to the back and stomach.

A pressurized aircraft nose landing gear strut assembly was being disassembled. The gland nut dislodged under pressure and made contact with an employee's left hand, breaking it.

A metal tooling base was being moved by a forklift when the load shifted. An employee who was assisting went to stabilize the load and prevent it from sliding off the forks. The C-channel of the base crushed the employee's left hand against the concrete ground, resulting in the amputation of their third and fourth fingers.

An employee was working on a tool platform (47.5" tall) and was transitioning around to the other side when they lost balance and fell to the concrete floor. The employee was hospitalized with fractures to seven ribs and their elbow.

An employee was adjusting the task lighting on a band saw when their right little finger made contact with the blade, resulting in amputation.

On August 19, 2025, at 6:30 a.m., an employee sat in the rear bench seat of a golf cart ahead of being driven to a parking lot. When the golf cart began to move, he fell off the cart and onto the ground, resulting in a fractured right hip.

An employee was working to remove a product blockage from a piece of equipment. The employee was struck by a metal bar near the deck of the pin mixer equipment and sustained blunt force trauma to the torso.

An employee was moving a rack onto a lower conveyor in the south heat treat area when their finger got caught between the part tray and the rollers, resulting in a fingertip fracture and amputation.

An employee was climbing a ladder to get on top of the breakroom. The ladder slipped, causing him to fall to the ground. The employee sustained fractures to his upper back, left foot, and ankle.

Two employees were removing a circuit breaker. The injured employee was using wrenches in the removal process. One of the wrenches contacted an adjacent door, resulting in an arc flash. The employee suffered burns to their neck, face, and ear, as well as momentary vision loss due to the flash.

An employee bent over to pick up a rubber mat from the ground. When he grabbed the corner of the mat, a rattlesnake hidden under it bit his left middle finger near the first knuckle. He was hospitalized.