Direct exposure to electricity, unspecified · Second degree electrical burns
At a glance
Federal OSHA recorded a severe workplace injury
at FIBA Technologies, Inc., 1531 Grafton Road, MILLBURY, MASSACHUSETTS 01527
on — Second degree electrical burns, affecting the multiple body parts, n.e.c..
Final narrative
An employee was replacing fuses in a bus duct disconnect switch in preparation to return an overhead crane to service. When inserting the B phase fuse, an arc flash occurred. The employee sustained second-degree electrical burns to the face and right arm and was hospitalized.
HospitalizedMultiple body parts, n.e.c.Switchboards, switches, fuses
An employee was installing a 15-amp breaker in an electrical panel when a 12-gauge ground wire touched the positive busbar of the panel, resulting in an arc flash. The employee sustained a second-degree burn to their left hand.
An employee was repairing an HVAC system in the drop tile ceiling of a conference room when they were shocked, causing them to fall from the ladder. The employee sustained burns to their right middle and ring fingers.
An employee was replacing a contactor inside an electrical panel attached directly to a press. The press itself was receiving power from another main panel. After replacing the contactor, the employee flipped the switch and an arc flash occurred, burning the employee's elbow, bicep, and neck.
An employee was attempting to switch a medium-voltage primary cable and install a 200-amp fuse barrel. The employee contacted the bottom of the switch gear cradle for the fuse barrel, causing an arc blast. The electricity entered the employee s left hand and exited his big toes, resulting in electric shock and burns to the left hand, arm, shoulder, and both feet. The employee was hospitalized.
On December 6, 2023, an employee of Duke Energy was working on a single-phase 120-/240-volt parallel service re-tap when a secondary flash occurred in an underground service. The employee suffered a second-degree burn to the face and was hospitalized.
More severe injuries in this industry (NAICS 423830)
An employee was sorting sucker rods. His right hand was caught in the area where the rod hits up against the frame and his index fingertip was amputated just below the nail.
An employee was using a powered miter saw to cut 2x4's. The saw blade hit something inside a board (possibly a hidden nail) and jumped, causing a laceration to the employee's left forearm. The employee was hospitalized with soft tissue and tendon injuries that required surgery.
A crane had been used to set a steel plate on a steel frame. An employee was trying to remove a clamp from the plate when the plate fell and crushed the tip of his left little finger. The employee sustained a fingertip amputation.
An employee was operating a scissor lift, raised to a height of about 15 feet, to inspect an overhead crane rail. The crane itself was being moved. Its hook swung into the scissor lift s arms, causing the lift to tip over onto its side, which in turn caused the lift and the employee to fall to the floor. The employee suffered injuries including broken ribs, spinal fractures, scapula fractures, and internal injuries.
A technician was operating a crane hoist to lift/remove a cylinder head from the main engine (port). The load was lifted at an angle, causing the cylinder head to get stuck on the cylinder head studs. When it became free from the studs, the cylinder head swung. It struck the technician and caught them against the cabinet door. This resulted in an amputation of their left index fingertip at the distal knuckle.
An employee fell while exiting a trailer. The employee landed on their left side on the pavement, suffering multiple broken ribs on the left side. The employee was hospitalized.
Two employees were setting up a mandrel in the spindle of a machine. The mandrel was side-shifted while an employee's hand was on the mast of a powered industrial truck. The employee suffered crushing injuries that resulted in amputations to the middle and ring fingertips.
An employee had been loading a double deck press. The employee saw a mold had been sent in with the C-hook still attached on the belly bar. As he went to remove the hook from the mold, his right thumb got caught on the C-hook. The employee's thumb was partially amputated.
An employee was operating a roller and paving a small pathway next to a pavilion. The ground was on a slight pitch, causing him to reach up toward the roll cage to stabilize himself. His right fifth finger was pinched between the roll cage and the rafter of the pavilion. The employee sustained a partial degloving injury with partial traumatic amputation.
An employee was delivering home heating fuel when bees came from the ground and stung the employee's face, neck, torso, and hands. The employee proceeded to shut off the oil flow before losing consciousness. They were hospitalized due to an anaphylactic reaction.