ENGINEERED FLOORS, LLC

On October 25, 2024, an employee was operating a warper and had just completed a full beam. He doffed the completed beam onto the floor. The empty beam, which is stored overhead, came down as the employee's left hand was guiding the completed beam. This resulted in the amputation of the little finger.

On April 29, 2024, an employee was replacing a wheel on a toolbox when it came down on his right middle finger, pinching it between the toolbox and the steel fork of a forklift. The fingertip was amputated.

An employee was clearing out cones of yarn in a warehouse after a small fire the previous day. A case of yarn (destabilized by the fire and the water that had been used to suppress it) began to fall. As the employee turned to run away, cones of yarn fell out of the case and broke his right ankle.

On September 18, 2021, at approximately 11:08 PM, a maintenance employee was repairing a heatset tunnel exit roller. The rubberized coating on the exit roller ruptured, blowing pressurized steam and hot water onto the employee. The employee was hospitalized with second and third degree burns to the left arm, abdomen, and back.

An employee was looking for defects in a carpet while standing on the floor between a catwalk and the exit roller of a tufting machine. He stepped backward and tripped on the edge of the catwalk, grabbing onto the exit roller of the machine with his left hand in order to catch himself. While doing so, his left index finger went into the keyway hole on the rotating exit roller, which caused his left index finger to be lacerated.

An employee was driving a cart around the driving range to pick up golf balls. The vehicle struck an in-ground target causing the employee to strike his forehead on the windshield. The employee was hospitalized with fractures to their nose and cheekbone and lacerations to their head and hands.

An employee was operating a picker when it struck a stack of pallets. His body moved forward and he struck his face on the computer monitor in the vehicle, resulting in a concussion, laceration, and blurry vision.

An employee was driving a lift in reverse through an aisle while the lift was loaded with a headboard. The headboard caught merchandise in the aisle racks, causing it to shift and contact the employee's right leg. The employee suffered a broken leg.

An employee was driving a utility task vehicle (UTV) through the parking lot to the boat yard to meet a co-worker. The UTV and slid into a curb, causing it to flip on its side and land on the employee's leg, resulting in a broken leg.

On December 7, 2023, an employee was driving an order picker down an aisle when the mast of the vehicle struck a material pan that was hanging out of the rack. The pan fell and struck the employee, resulting in rib fractures and a spleen laceration.

On September 10, 2025, an employee was working to fix a slipping carpet on a conveyor. He went to lift the carpet and put it back on the top rail when the conveyor belt caught his right hand and a roller subsequently caught his arm. The employee was hospitalized with a broken forearm.

On July 31, 2025, two employees were walking near a friction wash tank when a rubber gasket on top of the tank blew. Hot water mixed with 50% caustic chemical sprayed out and rained down on the employees. Both employees were brought to an emergency shower and were neutralized with vinegar. One employee was hospitalized with chemical and thermal burns to their upper back and eyes.

On May 27, 2025, an employee had been sweeping the floor around the sort and grind line conveyor. She was wiping down the frame of the conveyor when her right arm was drawn up between the conveyor belt and the snub roller underneath the conveyor. She sustained fractures to her upper and lower arm.

On January 29, 2025, an employee was operating an extrusion machine. He put a broken piece of yarn on the secondary roller and his glove was pulled into the nip rollers. The employee's left little fingertip was partially amputated.

On December 20, 2024, an employee was preparing to remove the access panel for the rotary valve gear box underneath a washer in polymerization. When he began loosening the bolts from the rotary lock cover, hot water and steam pressure released and caused second-degree burns to the employees stomach, both thighs, and the left calf area.

An employee was helping to lift the grating from a floor draining system when the grating slipped and landed on his hand, resulting in the amputation of his right middle finger at the first joint.

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

During a workshop meeting in a hotel, an employee heard a drilling noise, so he walked outside to see what it was. An explosion occurred (possible gas line) and his face, ear, and hair were burned. He also fell and sustained a pelvic fracture.

An employee slipped on condensation on a walkway in a parking garage. She fell and suffered a closed fracture to the neck of the left femur.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.