ENGINEERED FLOORS, LLC

On October 25, 2024, an employee was operating a warper and had just completed a full beam. He doffed the completed beam onto the floor. The empty beam, which is stored overhead, came down as the employee's left hand was guiding the completed beam. This resulted in the amputation of the little finger.

On April 29, 2024, an employee was replacing a wheel on a toolbox when it came down on his right middle finger, pinching it between the toolbox and the steel fork of a forklift. The fingertip was amputated.

An employee was operating a forklift when the vehicle struck a support beam. The employee sustained a contusion to his left rib.

On September 18, 2021, at approximately 11:08 PM, a maintenance employee was repairing a heatset tunnel exit roller. The rubberized coating on the exit roller ruptured, blowing pressurized steam and hot water onto the employee. The employee was hospitalized with second and third degree burns to the left arm, abdomen, and back.

An employee was looking for defects in a carpet while standing on the floor between a catwalk and the exit roller of a tufting machine. He stepped backward and tripped on the edge of the catwalk, grabbing onto the exit roller of the machine with his left hand in order to catch himself. While doing so, his left index finger went into the keyway hole on the rotating exit roller, which caused his left index finger to be lacerated.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.

An employee was rigging I-beams. An I-beam slid off the stack of I-beams and fractured the employee's leg.

On September 10, 2025, an employee was working to fix a slipping carpet on a conveyor. He went to lift the carpet and put it back on the top rail when the conveyor belt caught his right hand and a roller subsequently caught his arm. The employee was hospitalized with a broken forearm.

On July 31, 2025, two employees were walking near a friction wash tank when a rubber gasket on top of the tank blew. Hot water mixed with 50% caustic chemical sprayed out and rained down on the employees. Both employees were brought to an emergency shower and were neutralized with vinegar. One employee was hospitalized with chemical and thermal burns to their upper back and eyes.

On May 27, 2025, an employee had been sweeping the floor around the sort and grind line conveyor. She was wiping down the frame of the conveyor when her right arm was drawn up between the conveyor belt and the snub roller underneath the conveyor. She sustained fractures to her upper and lower arm.

On January 29, 2025, an employee was operating an extrusion machine. He put a broken piece of yarn on the secondary roller and his glove was pulled into the nip rollers. The employee's left little fingertip was partially amputated.

On December 20, 2024, an employee was preparing to remove the access panel for the rotary valve gear box underneath a washer in polymerization. When he began loosening the bolts from the rotary lock cover, hot water and steam pressure released and caused second-degree burns to the employees stomach, both thighs, and the left calf area.

An employee was helping to lift the grating from a floor draining system when the grating slipped and landed on his hand, resulting in the amputation of his right middle finger at the first joint.

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

During a workshop meeting in a hotel, an employee heard a drilling noise, so he walked outside to see what it was. An explosion occurred (possible gas line) and his face, ear, and hair were burned. He also fell and sustained a pelvic fracture.

An employee slipped on condensation on a walkway in a parking garage. She fell and suffered a closed fracture to the neck of the left femur.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.