105,313Records 71,083Employers 85,290Hospitalizations 27,770Amputations 2015-01-01 2025-10-31
Safety Incidents OSHA Severe Injury Reports · 2015–2025

ENGINEERED FLOORS, LLC

Contact incidents unspecified · Amputations, avulsions, enucleations unspecified

Federal OSHA recorded a severe workplace injury at ENGINEERED FLOORS, LLC, 1502 Coronet Drive, DALTON, GEORGIA 30720 on — Amputations, avulsions, enucleations unspecified, affecting the Finger or thumb tip(s), nail(s).

On April 29, 2024, an employee was replacing a wheel on a toolbox when it came down on his right middle finger, pinching it between the toolbox and the steel fork of a forklift. The fingertip was amputated.

Amputation Finger or thumb tip(s), nail(s) Boxes, crates, cartons

Engineered Floors, LLC

On October 25, 2024, an employee was operating a warper and had just completed a full beam. He doffed the completed beam onto the floor. The empty beam, which is stored overhead, came down as the employee's left hand was guiding the completed beam. This resulted in the amputation of the little finger.

ENGINEERED FLOORS, LLC

An employee was clearing out cones of yarn in a warehouse after a small fire the previous day. A case of yarn (destabilized by the fire and the water that had been used to suppress it) began to fall. As the employee turned to run away, cones of yarn fell out of the case and broke his right ankle.

ENGINEERED FLOORS, LLC

An employee was operating a forklift when the vehicle struck a support beam. The employee sustained a contusion to his left rib.

Engineered Floors, LLC.

On September 18, 2021, at approximately 11:08 PM, a maintenance employee was repairing a heatset tunnel exit roller. The rubberized coating on the exit roller ruptured, blowing pressurized steam and hot water onto the employee. The employee was hospitalized with second and third degree burns to the left arm, abdomen, and back.

Engineered Floors, LLC

An employee was looking for defects in a carpet while standing on the floor between a catwalk and the exit roller of a tufting machine. He stepped backward and tripped on the edge of the catwalk, grabbing onto the exit roller of the machine with his left hand in order to catch himself. While doing so, his left index finger went into the keyway hole on the rotating exit roller, which caused his left index finger to be lacerated.

View ENGINEERED FLOORS, LLC's full OSHA safety record →

HB Fleming, Inc.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Howard Industries Inc.

An employee was checking a pole-type transformer tank for leaks. A hydraulic clamping device was lowered onto his right thumb and crushed it against the sharp edge of the bottom of the tank. He suffered a partial transphalangeal amputation to the thumb.

3S Services, LLC

An employee had been cleaning the work area. While lifting a saw, the employee's index finger was lacerated by the saw blade. A tendon was cut and required surgery.

Broad & James, Inc.

An employee was installing a hydraulic extension cylinder in a tow truck when their leg was caught between the cylinder and the truck frame. The employee was hospitalized with a broken tibia, which required surgery.

TRC Services of Texas INC

An employee was sorting sucker rods. His right hand was caught in the area where the rod hits up against the frame and his index fingertip was amputated just below the nail.

NC Works Inc

On September 10, 2025, an employee was working to fix a slipping carpet on a conveyor. He went to lift the carpet and put it back on the top rail when the conveyor belt caught his right hand and a roller subsequently caught his arm. The employee was hospitalized with a broken forearm.

MOHAWK INDUSTRIES, INC.

On July 31, 2025, two employees were walking near a friction wash tank when a rubber gasket on top of the tank blew. Hot water mixed with 50% caustic chemical sprayed out and rained down on the employees. Both employees were brought to an emergency shower and were neutralized with vinegar. One employee was hospitalized with chemical and thermal burns to their upper back and eyes.

Mohawk Industries

On May 27, 2025, an employee had been sweeping the floor around the sort and grind line conveyor. She was wiping down the frame of the conveyor when her right arm was drawn up between the conveyor belt and the snub roller underneath the conveyor. She sustained fractures to her upper and lower arm.

Sprinturf, LLC

On January 29, 2025, an employee was operating an extrusion machine. He put a broken piece of yarn on the secondary roller and his glove was pulled into the nip rollers. The employee's left little fingertip was partially amputated.

Mohawk Industries, Inc.

On December 20, 2024, an employee was preparing to remove the access panel for the rotary valve gear box underneath a washer in polymerization. When he began loosening the bolts from the rotary lock cover, hot water and steam pressure released and caused second-degree burns to the employees stomach, both thighs, and the left calf area.

GS II Building Products, Inc.

An employee was helping to lift the grating from a floor draining system when the grating slipped and landed on his hand, resulting in the amputation of his right middle finger at the first joint.

US Battery Manufacturing Company, Inc

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

Alfa Insurance

During a workshop meeting in a hotel, an employee heard a drilling noise, so he walked outside to see what it was. An explosion occurred (possible gas line) and his face, ear, and hair were burned. He also fell and sustained a pelvic fracture.

EMORY UNIVERSITY HOSPITAL

An employee slipped on condensation on a walkway in a parking garage. She fell and suffered a closed fracture to the neck of the left femur.

Bull Moose Tube

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.