Spirit Aerosystems, Inc

A metal tooling base was being moved by a forklift when the load shifted. An employee who was assisting went to stabilize the load and prevent it from sliding off the forks. The C-channel of the base crushed the employee's left hand against the concrete ground, resulting in the amputation of their third and fourth fingers.

An employee was working on a tool platform (47.5" tall) and was transitioning around to the other side when they lost balance and fell to the concrete floor. The employee was hospitalized with fractures to seven ribs and their elbow.

An employee was working inside the access panel of a sliding door when the door began to shut. The employee's left middle finger was pulled into the chain and sprocket, resulting in amputation to the middle knuckle.

An employee was installing a rail on a machine. The roller pack was locked up, causing the chuck to not move. While manually removing the chuck, the rails were damaged. As a result, both the roller pack and the rail needed to be replaced. A fixed magnet from above the rail pulled the rail up and rolled it, pinching the employee's thumb between the rail and the magnet when he tried to install the new rail back to the position. The right thumb tip was amputated.

An employee was walking in the shop area, tripped on a work platform, and fell to the floor. The employee was hospitalized for a fractured femur.

An employee was walking through a parking garage. She tripped over a curb and fell forward onto her right knee, then her left knee, both hands, and her face. She suffered an injury to the left knee that required surgery, as well as scrapes on the chin and both palms and soreness in the left wrist.

An employee had been loading packages into a vehicle. While exiting the vehicle, he tripped and fell, fracturing both ankles.

An employee was exiting a train. The employee's foot was caught, and the employee fell, suffering a broken left arm.

An employee was dropping customers off with a shuttle. He stepped out of the shuttle and his foot entered a pothole, causing him to twist his ankle and then fall to the ground. The employee sustained multiple dislocations to the ankle requiring surgery.

An employee was approximately 5 feet up on a ladder while drilling a hole for cable installation. A wasp attacked him. As he was coming down the ladder, he landed flat on his feet on the ground, and his right leg was twisted. The employee sustained a fractured tibia.

A pressurized aircraft nose landing gear strut assembly was being disassembled. The gland nut dislodged under pressure and made contact with an employee's left hand, breaking it.

A metal tooling base was being moved by a forklift when the load shifted. An employee who was assisting went to stabilize the load and prevent it from sliding off the forks. The C-channel of the base crushed the employee's left hand against the concrete ground, resulting in the amputation of their third and fourth fingers.

An employee was working on a tool platform (47.5" tall) and was transitioning around to the other side when they lost balance and fell to the concrete floor. The employee was hospitalized with fractures to seven ribs and their elbow.

An employee was adjusting the task lighting on a band saw when their right little finger made contact with the blade, resulting in amputation.

On August 19, 2025, at 6:30 a.m., an employee sat in the rear bench seat of a golf cart ahead of being driven to a parking lot. When the golf cart began to move, he fell off the cart and onto the ground, resulting in a fractured right hip.

An employee was working to remove a product blockage from a piece of equipment. The employee was struck by a metal bar near the deck of the pin mixer equipment and sustained blunt force trauma to the torso.

An employee was moving a rack onto a lower conveyor in the south heat treat area when their finger got caught between the part tray and the rollers, resulting in a fingertip fracture and amputation.

An employee was climbing a ladder to get on top of the breakroom. The ladder slipped, causing him to fall to the ground. The employee sustained fractures to his upper back, left foot, and ankle.

Two employees were removing a circuit breaker. The injured employee was using wrenches in the removal process. One of the wrenches contacted an adjacent door, resulting in an arc flash. The employee suffered burns to their neck, face, and ear, as well as momentary vision loss due to the flash.

An employee bent over to pick up a rubber mat from the ground. When he grabbed the corner of the mat, a rattlesnake hidden under it bit his left middle finger near the first knuckle. He was hospitalized.