Contact with hot objects or substances · Thermal burns third degree or higher
At a glance
Federal OSHA recorded a severe workplace injury
at Parrish Enterprises, 1414 East Willow Road, ENID, OKLAHOMA 73701
on — Thermal burns third degree or higher, affecting the Foot (feet), toe(s) unspecified.
Final narrative
An employee was dipping an approximately 2-gallon ladle into a 300-pound furnace to fill the ladle with molten metal. The molten metal in the ladle fell onto the back of the employee's right pant leg. The metal burned through the employee's pants and fell down into their boots. The employee was hospitalized with second- and third-degree burns on their right foot.
An employee was grinding raw couplings on a belt sander to shave off excess material left by the manufacturing process. The employee's right hand slipped while he was pressing a part to the sander, causing his right thumb to come into contact with the sanding belt. The thumb was lacerated and broken, and the employee was hospitalized, requiring surgery.
An employee was working to reinsert a pin that had fallen out of a hydraulic table. The employee used a crane with an attached J-hook to lift the table. The hook slipped and the table fell down, crushing and amputating the employee's right index fingertip.
An employee pulled out a bucket of hot oil from under the fryer. The employee then stood on the table to clean the back wall. He stepped down into the bucket of hot oil, resulting in third-degree burns to his left leg.
An employee was performing maintenance under a kettle. When he removed a tri-clamp on a transfer line, the hot fat and broth material in the kettle poured out onto his arm. The employee was hospitalized with burns.
After completing a run with an oil distributor truck, an employee was working to return (suction) the hot oil to the tank of the truck. When the employee opened one of the valves, hot oil (approximately 385 degrees) sprayed their face, resulting in first-, second-, and third-degree burns.
An employee was filtering a fryer with a fryer filter machine. After going around the corner and then returning to the fryers, the employee stepped into the filter machine. The hot oil burned the employee's right ankle, and the employee was hospitalized.
An employee was using a water hose to clean debris out of the outfeed of a log conditioning vat. Water began entering the vat from the adjoining vat through a void in the separation wall at the infeed of the vats. As the employee was exiting the vat he had been working in using the access opening at the outfeed, hot water exiting the access opening entered the top of his protective hip wader. It pooled at the bottom of the wader and burned his left foot and ankle.
More severe injuries in this industry (NAICS 331524)
An employee was grinding raw couplings on a belt sander to shave off excess material left by the manufacturing process. The employee's right hand slipped while he was pressing a part to the sander, causing his right thumb to come into contact with the sanding belt. The thumb was lacerated and broken, and the employee was hospitalized, requiring surgery.
An employee was buffing a corner casting when the rotating belt contacted her right hand, resulting in an amputation of the first segment of her right thumb.
An employee was assembling boilers, which involved stacking the flat sections of boilers on top of one another and pushing them down a non-powered roller line. While the employee was pushing a stack onto the next set of rollers, the stack became crooked. The employee went to pull back the stack to straighten it when their finger was pinched by a roller. The employee sustained a partial amputation to their left ring fingertip.
On June 25, 2025, at 7.30 a.m., an employee was using a remote-controlled crane to change a die in a 2,600-ton press. They were releasing crane cables from the die when one cable did not release, causing the die to lift and pin the employee between the press and the die. The employee suffered a closed non-displaced fracture of the pelvis.
An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.
An employee was working in the food service warehouse when he experienced chest pain, difficulty breathing, and lost consciousness. The employee sustained carbon monoxide poisoning.
An employee was cutting a piece of metal rod with a metal cutting machine. His right middle finger became caught between the rod and the machine's table. The employee's fingertip was partially amputated.
An employee was working at her desk. She went to stand up and fell to the floor beside the desk. The employee sustained a hip displacement and required surgery.
An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.