Ignition of clothing from controlled heat source · Heat (thermal) burns, unspecified
At a glance
Federal OSHA recorded a severe workplace injury
at EVRAZ ROCKY MOUNTAIN STEEL, 1612 E. ABRIENDO AVE., PUEBLO, COLORADO 81004
on — Heat (thermal) burns, unspecified, affecting the multiple body parts, unspecified.
Final narrative
An employee was cleaning parts in a solvent tank when solvent spilled on the employee's clothing. The employee walked by a furnace and the solvent on their clothing caught on fire resulting in burns to the entire lower half of his body.
HospitalizedMultiple body parts, unspecifiedClothing, unspecified
More severe injuries at EVRAZ ROCKY MOUNTAIN STEEL
An employee was caught between the met hood and a column in the ladle refining furnace area. The employee was hospitalized for broken ribs and vertebrae and a punctured colon.
An employee was moving a pallet when a swing gate opened causing him to lose balance and fall through the opening approximately 8-9 feet to the ground.
An employee was welding metal parts. The employee turned to the left and their work uniform came in contact with the location on the part that had just been welded. The employee's uniform ignited, causing burns to their shoulder and back.
An employee was welding steel dump ramp slides. He leaned over and a previous weld caught his hoodie on fire. The employee sustained burns on his left side from the armpit to the waistline.
An employee was using a fiber wheel to cut a 55-gallon drum to make a trash can. As they were cutting, sparks flew into the barrel and fire came out of a hole on the barrel, catching the employee's shirt on fire. The employee sustained burns to their abdomen and chest, requiring hospitalization.
An employee was removing tubing caps and cleaning tubing ends with solvent. Their flame-resistant pants became soaked with the cleaning solvent and were ignited by a propane torch used for removing tubing caps. The employee was hospitalized with burns to their legs.
More severe injuries in this industry (NAICS 331111)
An employee used a crane to set down a bar. The bar measured 9 inches by 16 feet. The strap got stuck under the bar, and the employee asked another employee to jog the roll. The bar rolled and pinched the injured employee's left hand, resulting in a fingertip amputation.
An employee was loading a steel forming machine with steel to be processed. He went to move a cooling hose out of the way and his left thumb was crushed by the forming roller, resulting in injuries that required surgical amputation.
An employee was advancing a rail to line up for welding with a secondary rail on the weld line when his right middle and ring fingers were caught between the rails. The employee sustained an amputation to the top knuckle of the middle finger and a fracture to the ring finger. The machine was guarded at the time.
An employee was preparing bundles of 24-foot square metal tubing to be loaded onto a truck and cut the safety band for a bundle. While the employee was removing a piece of dunnage from a bundle, they bumped the bundle with their leg. The metal tubing then fell forward and struck the employee, causing a fractured left ankle.
An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.
An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.
A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.
An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.