Fall or jump curtailed by personal fall arrest system · Soreness, pain, hurt-nonspecified injury
At a glance
Federal OSHA recorded a severe workplace injury
at B & D Industrial, 1 Everitt Ave, PANAMA CITY, FLORIDA 32405
on — Soreness, pain, hurt-nonspecified injury, affecting the leg(s), unspecified.
Final narrative
An employee was working from an elevated platform, 35 feet high, while wearing a harness and retractable lanyard, to change out a gear on a paper machine. He fell from the platform an estimated 2 feet before the fall protection system caught him. He sustained some leg pain possibly due to the fall protection. He was hospitalized.
An employee was lowering machinery into a vat of caustic chemical using an electric hoist and crane. An I-bolt (screwed into the heavy machinery and also being held by the hoist) broke, and the machinery dropped into the vat. Caustic splashed the employee's clothing, who suffered burns and was hospitalized.
An employee was testing a two-stage hydraulic ram. The internal components of the ram blew out, puncturing his left forearm at the bottom and exiting at the top. The projectiles did not hit or break any bones.
An employee was walking along a trench inspecting the trench box in the excavation when he tripped and fell toward the trench. As the employee was falling head-first into the trench, he attempted to get a hold of the fall protection cable. The cable then looped around his left hand and the employee fell approximately 8 feet into the trench before the fall protection engaged. The employee suffered amputations of his left index, middle, ring, and little fingers.
A ranger was performing back-country patrol duties while hiking. As they were climbing a technical rock patch, a rock handhold broke, causing the employee to fall approximately 15 feet before their belay engaged. The employee contacted a rock, resulting in a fracture to the right ilium as well as a subcutaneous hematoma to the right gluteal region.
Employees were erecting structural steel. The injured employee was sitting on a 12" wide horizontal member and lining up an I-beam brace as it was suspended by an overhead crane. He leaned left to push the end of the brace. The end of the suspended brace swung away from him, causing him to lose balance and fall 8 feet. His personal fall arrest system arrested his fall, but he swung into a piece of duct work during the fall that resulted in a concussion.
On September 12, 2022, an employee was on a metal roof, installing a standing seam and insulation. He lost his balance and fell toward the third floor slab, which was 10 feet from the roof. His fall protection caught him and left him suspended about 2 to 4 feet from the slab. He suffered a brain bleed and a spinal fracture in his lower back. He was hospitalized.
An employee was working from a bucket lift, removing a tree in sections. He lost his balance while pushing on a section and fell. His fall protection caught him and he swung into a tree, suffering an injury that caused head, neck, and leg pain, as well as loss of consciousness while he was at the hospital.
More severe injuries in this industry (NAICS 423830)
An employee was sorting sucker rods. His right hand was caught in the area where the rod hits up against the frame and his index fingertip was amputated just below the nail.
An employee was using a powered miter saw to cut 2x4's. The saw blade hit something inside a board (possibly a hidden nail) and jumped, causing a laceration to the employee's left forearm. The employee was hospitalized with soft tissue and tendon injuries that required surgery.
A crane had been used to set a steel plate on a steel frame. An employee was trying to remove a clamp from the plate when the plate fell and crushed the tip of his left little finger. The employee sustained a fingertip amputation.
An employee was operating a scissor lift, raised to a height of about 15 feet, to inspect an overhead crane rail. The crane itself was being moved. Its hook swung into the scissor lift s arms, causing the lift to tip over onto its side, which in turn caused the lift and the employee to fall to the floor. The employee suffered injuries including broken ribs, spinal fractures, scapula fractures, and internal injuries.
A technician was operating a crane hoist to lift/remove a cylinder head from the main engine (port). The load was lifted at an angle, causing the cylinder head to get stuck on the cylinder head studs. When it became free from the studs, the cylinder head swung. It struck the technician and caught them against the cabinet door. This resulted in an amputation of their left index fingertip at the distal knuckle.
An employee was helping a coworker transport a tall palm tree with a mini skid steer. The employee was severely shocked by a high-voltage electrical wire above the ground.
An employee was retrieving a Christmas tree from a shelf using a ladder. He missed a step and fell to the concrete floor. He sustained injury to his head and wrist.
An employee was operating an agricultural tractor during sugarcane harvesting. The employee sustained a lumbar sprain due to vibration or motion from the tractor.
An employee was moving a 3-ton condensing unit, strapped down on a dolly, out of a garage. The strap broke, causing the employee to fall backward onto the brick pavered driveway. The employee suffered injury to a spinal ligament in the neck.