Crown Lift Trucks

An employee was operating a lift truck when it struck a stationary lift truck. His left thumb was pinched between the two lift trucks, resulting in a partial amputation.

On June 6, 2025, an employee was performing maintenance on a vertically-stored dock leveler. After completing the hydraulic repair, the employee went to exit the work area when their pant leg got caught on the bumper of the dock leveler. This caused the employee to lose their balance and fall out of the open dock door, approximately 37.5 inches. The employee sustained a lower left leg fracture.

An employee was manually moving a forklift battery in its compartment when her right index finger was pinched between the battery and the top of the compartment. The employee sustained a fingertip amputation.

On April 30, 2024, while at a customer location loading equipment onto a flatbed trailer for transport, an employee was injured when the trailer settled downward and pinched the employee's left foot between the equipment being loaded and the dock plate. The foot was fractured.

An employee was installing a dock leveler at a customer location. Cardboard was under the plate and a pry bar was used to lift the dock plate to remove the cardboard. The pry bar shifted and the dock plate fell on the employee's left ring and middle fingertips resulting in amputations.

An employee was drying and finishing vehicles when a vehicle door closed on their left middle fingertip and amputated it.

An employee was climbing down from a tractor trailer bed when they lost their footing and grabbed onto the roll-up door to stop the fall. The roll-up door then fell onto the employee's hand, resulting in a hand fracture that required surgery.

An employee was attempting to remove a tarp from a flatbed trailer when the trailer handle struck the employee in the chest, resulting in two broken ribs and a punctured lung.

An employee was near a backhoe while the operator was getting a broom. The broom handle struck the lever that actuates the swing of the backhoe bucket. The bucket then struck the injured employee, pinning him to the outrigger. The employee suffered crush injuries to the chest.

The injured employee was being trained on loading trucks in the load out bay. The injured employee and his supervisor climbed the stairs that run parallel to the truck and trailer, walked to the upper platform used for observation and sample taking, and saw that the lid of the grain trailer was closed. The employees began working to open the lid which appeared to be stuck due to cold weather. The injured employee pulled on one of the pivot arms that connect the lid to the main body of the trailer. As the lid began to open, the employee s right hand slipped down on the pivot arm and his index finger was caught between the pivot arm and the base of the pivot arm. The employee s right index finger was fractured and three nerves were severed. The employee was hospitalized.

An employee was sorting sucker rods. His right hand was caught in the area where the rod hits up against the frame and his index fingertip was amputated just below the nail.

An employee was using a powered miter saw to cut 2x4's. The saw blade hit something inside a board (possibly a hidden nail) and jumped, causing a laceration to the employee's left forearm. The employee was hospitalized with soft tissue and tendon injuries that required surgery.

A crane had been used to set a steel plate on a steel frame. An employee was trying to remove a clamp from the plate when the plate fell and crushed the tip of his left little finger. The employee sustained a fingertip amputation.

An employee was operating a scissor lift, raised to a height of about 15 feet, to inspect an overhead crane rail. The crane itself was being moved. Its hook swung into the scissor lift s arms, causing the lift to tip over onto its side, which in turn caused the lift and the employee to fall to the floor. The employee suffered injuries including broken ribs, spinal fractures, scapula fractures, and internal injuries.

A technician was operating a crane hoist to lift/remove a cylinder head from the main engine (port). The load was lifted at an angle, causing the cylinder head to get stuck on the cylinder head studs. When it became free from the studs, the cylinder head swung. It struck the technician and caught them against the cabinet door. This resulted in an amputation of their left index fingertip at the distal knuckle.

An employee was helping to lift the grating from a floor draining system when the grating slipped and landed on his hand, resulting in the amputation of his right middle finger at the first joint.

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

During a workshop meeting in a hotel, an employee heard a drilling noise, so he walked outside to see what it was. An explosion occurred (possible gas line) and his face, ear, and hair were burned. He also fell and sustained a pelvic fracture.

An employee slipped on condensation on a walkway in a parking garage. She fell and suffered a closed fracture to the neck of the left femur.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.