Struck by suspended or swinging objects n.e.c. · Amputations, avulsions, enucleations unspecified
At a glance
Federal OSHA recorded a severe workplace injury
at JLG Industries, Inc., 560 Walnut Bottom Road, SHIPPENSBURG, PENNSYLVANIA 17257
on — Amputations, avulsions, enucleations unspecified, affecting the Finger or thumb tip(s), nail(s).
Final narrative
An employee was winching in the mid-section of a boom on an aerial lift into the base section when their left middle and ring fingers were pinched between the two sections of the boom subassembly. The employee sustained a displaced fracture of the middle phalanx of their left middle finger and the amputation of their left ring fingertip.
Amputation Finger or thumb tip(s), nail(s) Vehicle and mobile equipment parts n.e.c.
An employee was preparing to use a programmable automated vertical band saw. The employee was clamping a piece of angle iron in place on the machine when the clamp caught the employee's left index fingertip. The employee suffered an amputation to the fingertip, up to the edge of the nail.
An employee was standing on the floor inspecting parts for paint quality. When he was finished looking at a part, he starting walking backwards and tripped on a wooden pallet that was laying on the floor behind him. He fell to the concrete floor and fractured a hip.
A welder was removing a steel production part from a welding fixture using an overhead crane. He connected the lifting hook to the steel part's center post, then applied tension to the overhead crane. His little finger was pinched between the lifting hook and the steel part, causing the amputation of the tip.
An employee was assembling a boom lift, inserting and sliding a section of boom into another boom section. The underside of her left middle finger was pinched the two sections, resulting in a partial amputation to the fingertip.
An employee was walking into the motor control center (MCC) room when his right ring finger was caught in the hinge of a doorway. He sustained an open phalanx fracture, which resulted in a partial amputation above the first knuckle.
An employee was stacking concrete blocks for a concrete bunker. As a block was swinging into place, the employee's left leg was pinched between two blocks, resulting in injuries to his left heel and lower leg.
An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.
An employee was placing a board on top of a bundle of steel tubing. A crane was moving a bundle of steel that struck the employee and caught them against another bundle of steel tubing. The employee sustained a crushing injury and hematoma to the right upper leg.
Employees were using a crane to lower large tree stems and branches while removing limbs and branches from the load. This caused the load to shift and strike an employee in the back, resulting in a hematoma on the lower left part of their back and a fractured ankle.
More severe injuries in this industry (NAICS 423830)
An employee was sorting sucker rods. His right hand was caught in the area where the rod hits up against the frame and his index fingertip was amputated just below the nail.
An employee was using a powered miter saw to cut 2x4's. The saw blade hit something inside a board (possibly a hidden nail) and jumped, causing a laceration to the employee's left forearm. The employee was hospitalized with soft tissue and tendon injuries that required surgery.
A crane had been used to set a steel plate on a steel frame. An employee was trying to remove a clamp from the plate when the plate fell and crushed the tip of his left little finger. The employee sustained a fingertip amputation.
An employee was operating a scissor lift, raised to a height of about 15 feet, to inspect an overhead crane rail. The crane itself was being moved. Its hook swung into the scissor lift s arms, causing the lift to tip over onto its side, which in turn caused the lift and the employee to fall to the floor. The employee suffered injuries including broken ribs, spinal fractures, scapula fractures, and internal injuries.
A technician was operating a crane hoist to lift/remove a cylinder head from the main engine (port). The load was lifted at an angle, causing the cylinder head to get stuck on the cylinder head studs. When it became free from the studs, the cylinder head swung. It struck the technician and caught them against the cabinet door. This resulted in an amputation of their left index fingertip at the distal knuckle.
An employee was walking into the motor control center (MCC) room when his right ring finger was caught in the hinge of a doorway. He sustained an open phalanx fracture, which resulted in a partial amputation above the first knuckle.
An employee was changing the spacing on a telehandler's forks. A fork slipped, and the employee's left index finger was caught between it and the mast. The fingertip was medically amputated at the first knuckle.
An employee was pulling down a broken skid with a forklift. When the employee backed up the forklift to get the forks out of the skid he pulled down, he contacted the forks of another parked forklift, fracturing both of his legs. He was hospitalized.
An employee was carrying cups back to the kitchen when her foot got caught on a cart and she fell face-first. During the fall, a piece of glass from a cup cut the inside of her mouth, severing an artery. She also sustained a laceration on her lower lip. The employee was hospitalized.